background image

5.1.8

         After modules are installed, the cables 
should be fixed or tied to avoid exposed 
under direct sunlight after installation, 
which would prevent cable from aging. 
Low-hanging cables can cause various 
problems, such as electric leakage and 
fire.

5.1.9

             T h e   a p p l i c a t i o n   l e v e l   o f   m o d u l e  
produced by Jolywood is Class A. modules 
with different color should be avoided from 
installed in the same array or roof.

5.1.7

         When installing modules, do not work 
alone, and keep working with a team of two 
or more men.

5.1.6

         Do not damage the back glass of module when 
modules mounted on the bracket. If module sneed 
to be replaced, do not damage the surrounding 
modules or mounting structure.

5.1.3

         When installing modules, only work in a 
dry environment with dry tools. Do not work 
in a humid environment without wearing any 
protective measures. Do not install modules 
under any rainy, snowy or windy conditions. 
Keep the connectors dry and clean when 
installing modules to avoid the risk of electric 
shock. If the terminal of the module is wet, 
no work could be done, otherwise electric 
shock may be caused. Modules should be 
installed immediately after unpacked.

5.1.4

         Do not wear metal rings, wristwatches, 
earrings, nose rings, lip rings, or other metal 
materials when installing or repairing PV systems.

5.1.5

         Use opaque materials to cover the module 

completely during installation. Do not open the
electrical connection or pull out the connector 
while the circuit is under load. Do not touch the
modules during installation unless necessary. 
Glass surfaces and brackets may have high
temperature, which might lead to the risk of 
hazards of burns and electric shock.

5.1.2

         Do not remove module package before 
installation.

5.1  Installation Safety

5.1.1

         The modules produced by Jolywood could 
installed landscape or portrait, the influence 
of shading effect caused by dust could be 
minimized when installed landscape.

the product has been tested to verify its
resistance to ammonia, which may be present 
near the cowshed, whether it could work in a 
wet(coastal) areas, areas where sandstorms 
occur frequently are also tested.

8

Jolywood (Taizhou) Solar Technology Co.,Ltd.

Kaiyang Rd., Jiangyan Economic Development zone, Taizhou City, Jiangsu Province, P. R. China

www.jolywood.cn

 mkt@jolywood.cn

 +86-523-8061 2361

Installation Manual

 - Jolywood N-type Mono-crystalline Double Glass Module

Summary of Contents for JW-HD108N

















Reviews: