background image

INTRODUCTION

Thank you for choosing Dynamic Diamond Vacuum (DDV), a high-quality product

based on the newest state-of-the-art technology. We hope that this device will be

to your satisfaction and meet your expectations. We are continuously striving to

improve our products in our product segment and will continue to supply the

market with new equipment.

NOTICE!

1.These instructions are only for DDV36 Dust Extractors.

2. DDV36 Dust Extractors are designed to clean construction areas and be connected to

medium and large grinders and shot blasters etc. The machine is suitable for picking up dry,

non-flammable dust and debris in and indoor environment. It is not suitable for picking up

liquids.

3. Please pay particular attention to the safety regulations and safety instructions

4. Read the complete instruction manual before using.

5. All spare parts and accessories used with this device must be those specified by

 

Dynamic Diamond Tooling

.

6. Check before and after use that all the switches are in OFF position.

Environmental protection

The packaging material can be recycled. Please do not throw the packaging material into

household waste; please send it for recycling.

Old devices contain valuable materials that can be recycled; these should be sent for

recycling. Batteries, oil, and similar substances must not enter the environment. Please dispose

of your old devices using appropriate collection systems.

Summary of Contents for DYNAMIC DIAMOND DDV36
















Reviews: