Jorc KAPTIV-CS-HP-S Installation & Maintenance Instructions Manual Download | Manualshive

Page: 5 / 10

background image

5

INSTALLATION INSTRUCTIONS

5b. Top inlet connection.

Connect the outlet to an oil/water separator.

-We advise to use the outlet nipple delivered with the
KAPTIV-CS-HP-S. If it is necessary to use an
alternative nipple, make sure it has the correct
thread (1/4”BSP), do not over tighten!

7. Power cable connection

Remove the protection cab from the connector
and connect your power cable as shown.

5. Power cable connection

Remove the protection cap from the connector
and connect your power cable as shown.

9. Press and hold down the TEST button to
check the valve function.

10. Your KAPTIV-CS-HP-S is ready for
operation!

L

Power

Connection

-We advise to use the outlet nipple delivered with
the KAPTIV-CS-HP-S. If it is necessary to use an
alternative nipple, make sure it has the correct
thread (1/4”BSP), do not over tighten!

N

8. Slowly open the ball valve to restore
normal system pressure.

6b. Side inlet connection.

Connect the outlet to an oil/water separator.

«
...
3
4
5
6
7
...
»

Summary of Contents for KAPTIV-CS-HP-S











Reviews:

No comments

Related manuals for KAPTIV-CS-HP-S

Brand: mabe Pages: 29

Brand: Braun Pages: 4

Brand: Midea Pages: 28

Brand: German pool Pages: 17

Brand: Frymaster Pages: 24

Brand: N'DUSTRIO Pages: 134

Brand: Base aire Pages: 16

Brand: Daewoo Pages: 31

Brand: CombiSteel Pages: 31

Brand: Nicky Clarke Pages: 16

Brand: Mediclinics Pages: 24

Brand: Mediclinics Pages: 32

Brand: FrigidaireWasher Pages: 36

Brand: GE Pages: 3

Brand: GE Pages: 8

Brand: GE Pages: 12

Brand: GE Pages: 3

Brand: GE Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands