background image

 

 

 

 
 

 

7 | Warranty 

 

Warranty 

To not to adversely affect the warranty, the following notices must be adhered to.  

NOTICE 

 
Operating personnel must not remove equipment covers. Only personnel trained 
and certified by ALPHATRON MARINE must make component replacement and 
internal adjustment.  
 

NOTICE 

 
Do not disassemble or modify the equipment. Failure to observe this instruction 
may cause equipment failure, and it will void the warranty. 
 

NOTICE 

 
Any modification to this equipment without prior written permission from 
ALPHATRON MARINE will void the warranty. 
 

NOTICE 

 
Installation of this product shall only be done by a certified installation company 
approved by either ALPHATRON MARINE or by an official ALPHATRON MARINE 
distributor. Acting otherwise will void the warranty. 
 

NOTICE 

 
This product contains no operator serviceable parts. Service and repair shall only be 
carried out by personnel trained and certified by ALPHATRON MARINE. 
 

NOTICE 

 
Do not place a container containing liquid on the equipment. The equipment can be 
damaged if knocked over. 
 

NOTICE 

 
When cleaning the surface, do not use any organic solvent such as thinner or 
benzine. Otherwise, the paint and markings on the surface may get damaged. For 
cleaning the surface, remove the dust and debris and wipe with a clean dry cloth. 
 

 

 

 

 

 

Summary of Contents for Alphatron Marine Mode Switch 3 Pos













Reviews: