JRClancy SCENECONTROL 100 Operating Instructions Manual Download

Page: 2 / 15

Design, Manufacture and Installation of Theatrical Equipment Worldwide

(315) 451-3440

Fax (315) 451-1766

www.jrclancy.com

Rev 3: October 7, 2009

Table of Contents

Spread/Page

Introduction ......................................................................................... 1

System Overview................................................................................. 2

System Components........................................................................... 2

EMERGENCY STOP SYSTEM............................................................................ 2

MOTOR STARTERS............................................................................................ 2

LIMIT SWITCHES ................................................................................................ 3

End-of-travel limits ............................................................................................ 3

Limit switch types ............................................................................................. 3

WALL-MOUNT CONTROL STATION .................................................................. 3

PORTABLE CONTROL PENDANT ..................................................................... 4

System Operation................................................................................ 5

BASE SCREEN – MULTIPLE WINCH SYSTEMS ............................................... 5

WINCH BASE SCREEN....................................................................................... 5

WINCH OPERATION- DIRECT CONTROL ..................................................... 6

WINCH OPERATION- TARGET CONTROL .................................................... 7

RECORDING PRESETS...................................................................................... 7

STATUS PAGE .................................................................................................... 8

PARAMETER PAGE ............................................................................................ 9

LOAD SENSE PARAMETERS PAGE................................................................ 10

Load Learning................................................................................................. 11

SYSTEM PRESETS PAGE................................................................................ 12

SYSTEM PRESETS RECORD PAGE ............................................................... 13

Appendix I: Troubleshooting ........................................................... 13

Summary of Contents for SCENECONTROL 100
















Search results

Summary of Contents for SCENECONTROL 100

Reviews:

Related manuals for SCENECONTROL 100

Brands by name

Popular brands

JRClancy SCENECONTROL 100, Operating Instructions Manual

Search results

Summary of Contents for SCENECONTROL 100

Reviews:

Related manuals for SCENECONTROL 100

Brands by name

Popular brands