background image

25

ATTENTION!

Keep the warranty card for the entire duration of the warranty period.

With this warranty, the seller and the service center assume the obligation to remedy defects caused by the manufacturer at no 

charge during the warranty period. The warranty card is valid only if it correctly and clearly indicates: the model, serial number 

of the equipment, date of sale, clear seal of the seller.

Warranty repair may be refused in the following cases:

– information about the equipment in the card is incomplete, illegible, unreliable (discrepancy with the information on the equipment), there is no signature of the buyer;

– incorrect installation, improper transportation of the equipment, unsatisfactory condition of the condenser and lack of proper maintenance by the user (see Operating 

Manual);

– the presence of mechanical damage could lead to improper operating conditions or failure of the equipment;

– failure to comply with the terms of the manual in the equipment's operation or in case of false actions by customers;

– If a natural disaster or a standard insurance event has occurred, resulting in the impossibility of further operation of the equipment (flooding, fire, theft, etc.), as well as under 

other circumstances beyond the control of the seller, manufacturer.

– when traces of any foreign objects, liquids, insects, etc. are found inside the equipment, as a result of which the equipment has malfunctioned;

– unqualified repairs or any structural modifications to the system by unauthorized persons;

– if the damage defects occurred due to non-compliance of the stream and cable network parameters with the requirements of state standards.

WARRANTY MAINTENANCE DOES NOT COVER 

 periodic maintenance, installation, adjustment of equipment for operation, or cable replacement.

The warranty does not cover easily breakable parts of the equipment that are considered consumables by factory standards: lamps, glass, plastic 

(handles, etc.), rubber, locks, wheels, etc.

The above warranty service does not diminish the purchaser's legal rights granted by applicable law.

The buyer shall be notified that if a service technician is called to the location of the equipment and a non-warranty failure is found, the buyer shall 

reimburse the service technician for travel expenses and, if desired, use the service technician's services at the manufacturer or seller's rates to correct 

the defects in the equipment.

Summary of Contents for ADI125




























Reviews: