background image

3

Dear customer! If you have purchased equipment operating with R290 refrigerant, please read the reservations carefully before 

using this product.

Special warning notes for equipment with R290 refrigerant

Fluorinated greenhouse gases 

are in a hermetically sealed system. Work on the refrigeration and electrical systems of the equipment 

should only be performed by the manufacturer's qualified service technician. If this requirement is not met, warranty claims will not be 

considered.

• This equipment contains flammable and explosive refrigerant - propane R290!

• Be sure to maintain a minimum distance of 10 cm from the walls of the equipment to the walls and surrounding objects. In any case, 

do not allow the air circulation for equipment with a flammable refrigerant to be disrupted!

• Do not cover the ventilation holes in the equipment enclosure.

• The equipment must be disconnected from the mains before each maintenance.

• Work on the refrigeration system should only be performed by qualified specialists (specialists trained in handling flammable 

refrigerants).

• Open the refrigerant circuit and pump it out only in well-ventilated rooms or outdoors. Make sure there are no unauthorized people 

around.

• R290 propane refrigerant must be disposed of by authorized companies in compliance with all safety standards.

WARNING

• Do not allow damage to the refrigerant circuit.

• Do not use mechanical or other means to accelerate the defrosting process other than those approved by the manufacturer.

• Do not install any electrical devices in the storage chamber that are not intended by the manufacturer.

The manufacturer has the right to change the technical specification and characteristics of the equipment not impairing its functionality 

without prior notice to the customer. Illustrations, photos, pictures of equipment may differ from the real model.

Summary of Contents for ADI125




























Reviews: