– 102 –
2. Output terminal setup
Output No.
Contents
Explanation
0
Nil
No output
For the actuator
1
Feeding frame 1
Feeding frame right lifting
2
Feeding frame 2
Feeding frame left lifting
3
Feeding frame 3
(Feeding frame right 2-stage stroke)
4
Feeding frame 4
Feeding frame left 2-stage stroke
5
(Intermediate presser)
(Signal output)
6
Void
7
Reverse shaft
Reverse shaft setting side
8
Third thread tension
Third thread tension closed
9
Needle cooler
Needle cooler air output
For pattern data outputs
33
External output 0
Reverse signal output with the External Output 0 command of the pattern data
34
External output 1
Reverse signal output with the External Output 1 command of the pattern data
35
External output 2
Reverse signal output with the External Output 2 command of the pattern data
36
External output 3
Reverse signal output with the External Output 3 command of the pattern data
37
External output 4
Reverse signal output with the External Output 4 command of the pattern data
38
External output 5
Reverse signal output with the External Output 5 command of the pattern data
39
External output 6
Reverse signal output with the External Output 6 command of the pattern data
40
External output 7
Reverse signal output with the External Output 7 command of the pattern data
41
External output 8
Reverse signal output with the External Output 8 command of the pattern data
42
External output 9
Reverse signal output with the External Output 9 command of the pattern data
43
External output 10
Reverse signal output with the External Output 10 command of the pattern data
44
External output 11
Reverse signal output with the External Output 11 command of the pattern data
45
External output 12
Reverse signal output with the External Output 12 command of the pattern data
46
External output 13
Reverse signal output with the External Output 13 command of the pattern data
47
External output 14
Reverse signal output with the External Output 14 command of the pattern data
48
External output 15
Reverse signal output with the External Output 15 command of the pattern data
Status of sewing machine head
49
Needle upper position
Upper stop position
40 to 62
°
(Always ON shortly after Power ON)
50
Needle lower position
(Internal signal)
80 to 123
°
(Always OFF shortly after Power ON)
51
Needle upper dead point position
Reverse rotation needle lifting position 5 to 30
°
(Always OFF shortly after Power ON)
52
Needle lower dead point position
Lower stop position
209 to 239
°
(Always OFF shortly after Power ON)
53
Thread trimming signal
During thread trimming stop (not used)
ON beneath the needle shortly before stoppage
→
OFF at +70ms above the needle
54
During rotation
In the middle of sewing machine driving ON at the start of rotation
→
OFF at +120ms above
the needle
55
Sewing machine brake signal
During sewing machine stop
ON beneath the needle shortly before stoppage
→
OFF at +120ms above the needle
56
Void
Status of sewing machine unit
57
Status of setup
In the setup condition
58
Status of READY operation
Ready key
→
Origin retrieval
→
Moving to the sewing start point and thereafter
59
READY status
In the ready condition
60
Sewing status
From the start of sewing to the feeding frame lifting after moving to the sewing start point.
Feed forward included.
61
During sewing
From the start of sewing to the end of pattern data. Jump feed included.
62
Sewing machine in driving
In the middle of sewing machine head driving during sewing. Bobbin and needle lifting reset
not included.
63
Resetting to the sewing start point
From the end of pattern data to the reset of the sewing start point.
64
Sewing being stopped on the way
Stopped with a midway stop command of the pattern data.
65
Stop with sewing error display
Error display being presented because of error stop during sewing.
66
Temporary stop of sewing
Error stop during sewing or temporary stop after the promotion of stitching due to pattern
check, etc.
67
XY feeding operation
Jump feed during sewing, pattern check, feed forward/return motion, and others.
68
Origin reset
Origin reset key
→
Reset to the sewing start point
69
Presser lowering status
Presser lowering key
→
Presser lowering status