– 9 –
1) Turning the oil amount adjustment screw attached on the hook driving shaft front bushing in the “+” direction (in direc-
tion
A
) will increase the amount of oil (oil spots) in the hook, or in the “–” direction (in direction
B
) will decrease it.
2) After the amount of oil in the hook has been properly adjusted with the oil amount adjustment screw, make the sewing
machine run idle for approximately 30 seconds to check the amount of oil in the hook.
Ɣ
ϣ༶ᇧఴؑࣈඒҍࡸഏ֬ႹਏןᆣઋරསƖ֬١སƓ
A
١སƔሎƗႹਏƓࠝƔєئƗསƘ֬١སƓ
B
١སƔሎƗ
ႹਏƓࠝƔєങè
Ɣ
Ⴙਏןཞઋරןᆣޱ֬ႹࠝƗ႒३ᄕሎ ᇙႾ࣐ྡྷႹਏƓࠝƔ֬ಙಱè
1) 図の状態が油量(跡)適量を示します。縫製工程によっては調整が必要となりますが、あまり極端に増減しないで
ください。(少量 = 釜焼付(釜発熱)、多量 = 縫製品を汚す)
2) 油量(跡)は、3 回(3 枚)確認する中で変化しないよう調整してください。
1) The state given in the
fi
gure shows
the appropriate amount of oil (oil splashes). It is necessary to
fi
nely adjust the
amount of oil in accordance with the sewing processes. However, do not excessively increase/decrease the amount of
oil in the hook. (If the amount of oil is too small, the hook will be seized (the hook will be hot). If the amount of oil is
too much, the sewing product may be stained with oil.)
2)
Adjust the amount of oil in the hook so that the oil amount (oil splashes) should not change while checking the oil
amount three times (on the three sheets of paper).
Ɣ
൜ѝ൜Ⴙਏ Ⴙࠝ ൨ਏ֬መฆèಝۻओڐᇌ܄࿄֬ྺးႼढ़း࣐ྡྷшး֬ןᆣƗ֓౯ሆၰ҉းݝ؎׀ᅀ
Ⴙਏè
ƓႹਏݝങ൏Ɨ߽കߑ࿏෯ƓنಪƔ
èႹਏݝئ൏Ɨ߽ᄪڐᇌè
Ɣ
Ɣ
ႹਏƓႹࠝƔ႒ಙಱ Ɠ ᅭƔयєߋè
適量 ( 大 )/
Appropriate amount of oil (large) /
油量适当(大)
適量 ( 小 )/
Appropriate amount of oil (small)/
油量适当(小)
釜からの飛散油 /
Splashes of oil from the hook
/
从旋梭飞溅出来的油
釜からの飛散油 /
Splashes of oil from the hook
/
从旋梭飞溅出来的油
(3)釜油量(跡)適量見本 /
Sample showing the appropriate amount of oil in the hook /
旋梭油量(油迹)适合标样
1 mm
2 mm
1
油量(跡)確認用紙
Amount of oil (oil splashes) con
fi
rmation paper
油量(迹)确认专用纸
2
油量(跡)確認位置
Position to con
fi
rm the amount of oil (oil splashes)
油量(迹)确认位置
油跡確認用紙
Oil splashes con
fi
rmation paper
油迹确认专用纸
25 mm
70 mm
※ 以下 2)の作業を行う時は、面板を外し、指が天秤に触れないよう十分注意してください。
1) 冷えた頭部の場合は 3 分程度の空運転を行ってください。(適度な断続運転)
2) 油量(跡)確認用紙はミシンを運転した状態で挿入してください。
3) 油溜りの油面の高さは HI と LOW の範囲内にあることを確認してください。
4) 油量(跡)確認所要時間は 10 秒間で行ってください。(時計で計ってください。)
(4) 面部油量確認 /
Con
fi
rmation of the amount of oil supplied to the face plate parts /
面部油量确认
1) 下軸前メタルについている油量調節ねじを + の方向 (
A
方向 ) に回
すと油量 ( 跡 ) は多くなり、−の方向 (
B
方向 ) に回すと油量 ( 跡 )
は少なくなります。
2) 油量調節ねじで調整した後は、30 秒間程度の空運転を行い油量 ( 跡 )
確認を行ってください。
A
B
(2) 釜油量 ( 跡 ) 調整 /
Adjusting the amount of oil (oil spots) in the hook /
旋梭油量(迹)调整