Juliana Premium Wall, Assembly Instructions Manual

4

Dear Customer!

The assembly of your new house requires 

a bit of technical knowledge. However, it is 

important that the assembly instructions are 

followed strict-ly. The assembly instruction 

is a combination of text and illustrations. The 

profiles are packed in separate numbered packs 

corresponding to the order in the assembly 

instruction. Erect one pack at a time. All nuts 

and bolts and fittings are found in bag No. 0 

(specified on page 12). Each pack is specified in 

separate lists of components. 

All detailed illustrations are marked with 

symbols:

Seen from inside          Seen from outside.

Precautions.

• 

Assembly must only be carried out in dry 

and calm weather.

• 

Always use working gloves while glazing. 

Greenhouse glass has sharp edges, 

especially if the glass breaks.

• 

Assistants and especially children must be 

warned that broken glass is an element of 

danger. Pick up broken glass at once and 

remove it with care.

• 

We recommend to use protective glasses 

while fixing the spring wire clips.

• 

Place the ladder on a level support.

• 

It is essential to have an assistant.

References

The column marked              indicates the 

page(s) on which the component is used.

Page 13: 

Foundation

The base is not included in this delivery. 

However, an original base can be bought 

separately. It ensures you a stable and easy to 

build base. 

If you make your own base the measurements 

indicated must be external measurements.

If you buy an original base you furthermore 

need about 75 litres of concrete and 6/8 

plastic-/concrete pipes of about 800 mm which 

are placed in a non-freezing depth for the 

fastening of the corner and middle anchors.

The base must be 100% level and square; the 

latter is ensured by checking that the two 

diagonal measurements are equal.

Tools

The mounting of the greenhouse requires the 

tools shown on page 12.

Page 14-27:

Place the components as shown on the 

illustration and assemble in the order shown 

in the pictures. Do not tighten the nuts 

completely until the front gable construction 

has been assembled.

Page 13:

(Fastening to the base).

When constructing your own base you have 

to drill holes (7 mm) in the ground frame 

between all the vertical frames, the greenhouse 

is then fastened to the base with screws (A). 

Using an original base the greenhouse is 

fastened to each vertical bar as shown on 

drawing B/C.

Page 24-27:

For an easier assembly we recommend that you 

oil the screws for the doors.

Fitting of glass/polycarbonate

Important before glazing! 

Make sure that gables and sides are level and 

square, and that door(s) and window(s) are 

functioning perfectly. 

Best order of assembly:

1) Windows – 2) Roof – 3) Doors – 4) Gables 

– 5) Sides

Page 30-33:

Glazing (illustration 1 to 8)

Degrease the sheets and frames with spirit.

Start glazing from below, one glass at a time. 

Apply a 3 mm silicone line on the vertical 

frames where indicated (dotted lines on 

the illustration). (A 3 mm line of silicone is 

sufficient to obtain maximum attachment). If 

you do use more than recommended, you can 

buy extra tubes. 

Spring wire clips and glassholders are to be 

fitted as shown.

X = Spring wire clips, > = Glassholders

In case of broken glass carefully pull it 

outwards and loosen the silicone by means of a 

sharp craft knife.

Clean the profile completely before inserting a 

new pane of glass.

Page 34-37:

Mounting of polycarbonate 

The illustrations at the bottom of page 34/36 

show where to mount the polycarbonate plates 

and lists. The type indication states the length 

in mm. A possible adjustment is made by 

means of a fine-tooth saw. 

NB! To avoid the formation of algae the 

polycarbonate sheets must not come into 

contact with the ground. Rest them on a piece 

of cardboard.

A-lists are mounted as shown on page 35/37. 

Put the sheet into the bottom list, bend the 

sheet slightly outwards and put it in the top list.

M-lists are mounted as shown on page 35/37. 

Place the upper part of the list under the alu. 

profile in the whole length of the sheet and 

hereafter click on the list from above.

Sealing of the polycarbonate sheets

The sheets may be sealed against insects. 

Close the top end off with alu-tape or silicone. 

The bottom only with  airstrip tape to let 

condensation out (available at your local 

dealer).

Now your greenhouse is completely assembled. 

However, please notice the following:

Maintenance

• 

Grease doors (hinges and lock).

• 

Clean the gutter for leaves, etc.

• 

Adjustment of windows.

• 

Replacement of broken glass.

• 

Clean the house with disinfectant before 

and after the growing season.

Winter Protection

In areas with occurrence of snow we 

recommend the following winter protection:

• 

Support the roof ridge at the centre of the 

house.

• 

Remove greater snow loads from the roof.

• 

Take precautions against snow falling 

down from for instance a tree or a roof.

• 

Dismount the cylinders for the automatic 

window openers, if any (optional extras).

• 

Secure door(s) and window(s) preventing 

wind damage to the house.

Insurance

Please note that not all insurance companies 

cover glasshouses automatically. Please 

contact your insurance company to ensure an 

insurance coverage.

Guarantee

Juliana grants a guarantee of 12 years which 

covers replacement of faulty parts. The 

guarantee does not cover polycarbonate, glass, 

transport, assembly, freight etc. 

Juliana grants a guarantee of 2 years on painted 

parts, if any. Note that marks in the painting 

may occur due to suspension of the profiles. 

The guarantee is invalid if the greenhouse is 

not assembled according to these instructions.

Complaints

All our greenhouses are built to high standards 

of quality. However, should a complaint 

occur please contact your dealer at once. 

Remember to specify the defect by indicating 

the greenhouse model and number of the 

component and the quality control number.

May we congratulate you on your new greenhouse

GB

USA

DEAR CUSTOMER

Congratulations on purchasing your new 

greenhouse. It is important that you follow these 

assembly instructions step-by-step. 

The assembly instructions are a combination of text 

and illustrations. The profiles are packed in separate, 

numbered packs corresponding to their order of use 

in the instructions. Assemble one pack at a time. All 

nuts, bolts and fittings are contained in a Box. 

Each pack is specified in separate lists of 

components. 

All detailed illustrations are marked with the 

following symbols:

Seen from the inside     Seen from the outside

SOME SAFETY PRECAUTIONS

• 

Assembly must only be carried out in dry and 

calm weather.

• 

Always wear work gloves when installing the 

glazing. Greenhouse glass has sharp edges, 

especially if it breaks.

• 

Assistants and especially children must be 

warned that broken glass is dangerous. Pick 

up all broken glass at once and remove it with 

care.

• 

We recommend that you wear protective 

glasses while fixing the spring wire clips.

• 

Any ladders that are used must be placed on a 

level surface.

• 

It is essential to have an assistant available.

TOOLS

Assembling the greenhouse requires tools.

FOUNDATIONS

No base is included with this product. However, an 

original base is available separately. This base is easy 

to construct and will guarantee you a stable base for 

your greenhouse. 

If you construct your own base, the specified 

measurements must be external measurements.

The holes must be dug out to below the frost line. 

Place the assembled base with anchor legs over the 

holes so the anchor legs fit into the holes; it takes 

about 75 litres of concrete to fill up the holes.

Make sure the base is completely level and square. 

To square the base, make sure the two diagonal 

measurements are identical.

The width of the front and back gables must also be 

identical..

ATTACHMENT TO THE BASE

If you construct your own base, you must drill holes 

(Ø7) in the ground frame between all the vertical 

profiles. The greenhouse must then be secured to 

the base using screws (A). 

If you use an original base, the greenhouse must be 

secured to each vertical bar as shown on drawings 

B/C.

ORDER OF ASSEMBLY

Place the components as shown on the illustration 

and assemble in the order shown in the pictures. Do 

not tighten the nuts fully until the entire sub-frame 

has been assembled.

DOORS AND WINDOWS

For easier assembly, we recommend that you oil the 

screws for the doors. The glass or polycarbonate for 

the door(s) and windows must be fitted at the same 

time as the profiles.

FITTING OF GLASS/POLYCARBONATE

Important before assembly! 

Make sure that the gables and sides are level 

and square and that door(s) and window(s) are 

functioning perfectly. 

The best order of assembly for the glass or 

polycarbonate is as follows:

Windows - Roof - Doors - Gables - Sides

GLASS INSTALLATION

Glass installation (illustrations 1 to 8)

Degrease the sheets and frames with ethanol.

Start glazing from the bottom, one pane at a time. 

Apply a 3mm silicone bead around the vertical 

frames as indicated (the dotted lines on the 

illustration). (A 3mm bead of silicone is sufficient to 

ensure maximum adhesion). If you use more silicone 

than recommended, extra tubes can be purchased. 

Spring wire clips and glass-holders must be fitted as 

shown.

X = Spring wire clips, > = Glass-holders

If you accidentally break a pane, carefully pull the 

broken glass outwards and loosen the silicone using 

a sharp craft knife.

Clean the profile completely before inserting a new 

pane of glass.

POLYCARBONATE INSTALLATION

The type designation states the length in 

millimetres. If adjustment is necessary, use a fine-

tooth saw. 

NB! To avoid the growth of algae, prevent the 

polycarbonate sheets from coming into contact with 

the ground by resting them on a sheet of cardboard.

A-strips. 

Insert the sheet into the bottom strip, bend the 

sheet slightly outwards and insert it into the top 

strip.

M-strips.

Place the upper part of the strip under the 

aluminium profile along the full length of the sheet 

and then click the strip into position from above.

U-strips. 

Fit the strip to the sheet and adjust the length.

If desired, the sheets may be sealed against insects. 

Seal the top using aluminium tape or silicone. The 

bottom should only be sealed with air-strip tape to 

allow condensation to escape (available from your 

local dealer).

Your greenhouse is now fully assembled. However, 

please note the following:

MAINTENANCE

• 

Grease the doors (hinges and locks).

• 

Keep the gutters free from leaves, etc.

• 

Adjust the windows as necessary.

• 

Replace any broken glass.

• 

Clean the greenhouse with disinfectant before 

and after the growing season.

WINTER PROTECTION

If you anticipate snow during the winter, we 

recommend the following winter precautions:

• 

Support the apex of the roof in the middle.

• 

Remove any deep snow from the roof.

• 

Take precautions to prevent snow falling from 

a tree or roof, for example.

• 

Remove the cylinders for the automatic 

window openers, if fitted (optional extras).

• 

Secure the door(s) and window(s) to prevent 

wind damage to the greenhouse.

WATER AND CONDENSATION

Please note that your greenhouse is not like a 

conservatory, for example, and that you should 

therefore be aware that the greenhouse may leak 

during or after precipitation and that condensation 

will occur on the inside of the greenhouse. Good 

ventilation will help prevent condensation.

INSURANCE

Please note that not all insurance companies cover 

greenhouses automatically. Please contact your 

insurance company to ensure that your greenhouse 

is covered.

GUARANTEE

Juliana greenhouses are covered by a 12-year 

guarantee, which covers the replacement or repair 

of faulty parts. The guarantee does not cover 

polycarbonate, glass, transport, assembly, freight, 

etc. 

Juliana greenhouses are covered by a two-year 

warranty on painted parts, where fitted. Note that 

marks on the paint may occur due to suspension of 

the profiles. 

The guarantee will be void if the greenhouse is not 

assembled in accordance with these instructions.

COMPLAINTS

All our greenhouses are built to the highest quality 

standards. However, should you experience any 

problems, please contact your dealer at once. When 

describing the defect, please state the greenhouse 

model, the component number. 

Congratulations on your new greenhouse, which we 

hope will bring you a lot of pleasure for many years 

to come.

Yours sincerely,

Juliana Drivhuse A/S