background image

eNet radio dimming actuator 1-gang mini

eNet radio dimming actuator 1-gang mini
Art. no.: FMUD20250UP

Operating instructions

1

Safety instructions

Electrical devices may only be mounted and connected by electrically skilled persons.

Serious injuries, fire or property damage possible. Please read and follow manual fully.

Danger of electric shock. Always disconnect before carrying out work on the device or load. In
so doing, take all the circuit breakers into account, which support dangerous voltages to the
device and or load.

Danger of electric shock. Device is not suitable for disconnection from supply voltage. The load
is not electrically isolated from the mains even when the device is switched off.

Risk of destruction if the set operating mode and load type do not match. Set correct operating
mode when connecting or exchanging the load.

Fire hazard. For operation with inductive transformers, each transformer must be fused on the
primary side in accordance with the manufacturer's instructions. Only safety transformers ac-
cording to EN 61558-2-6 may be used.

These instructions are an integral part of the product, and must remain with the end customer.

2

Intended use

Switching and dimming of lighting

Operation with suitable radio transmitters

Mounting in appliance box according to DIN 49073 in combination with a suitable cover

Installation in surface-mounted housing or panel-mounted housing (accessories) for sus-
pended ceilings

Product characteristics

Switch-on via bulb-preserving soft start

Switch-on brightness can be saved permanently

Minimum brightness can be saved permanently

Scene operation possible

Status indication with LED

Status feedback to radio transmitter

Switchable with Prog. button

Electronic short-circuit protection with permanent switch-off after 7 seconds at the latest

Electronic over-temperature protection

Automatic or manual setting of the dimming principle suitable for the load

Power extension possible by means of power boosters

Can be set with eNet server:

Maximum brightness

Dimming speed

Switch-on delay / switch-off delay

Dim up/dim down ramp

Switch-off warning

Operation locks

Continuous on, Continuous off

Hotel function

Run-on time

1 / 16

82580733

14.10.2019

J0082580733

Summary of Contents for FM J 50700 UP

















Reviews: