background image

eNet radio switch/push-button actuator in SCHUKO housing

Parameters

Setting options, Basic setting

Explanations

Deactivate wind alarm switch-
ing state

On, Off
Basic setting: Off

Defines the behaviour of the
output on deactivating the
wind alarm. Only visible when
the priority for the wind alarm
is 0.

Priority, sun protection

0...4
Basic setting: 0

Specifies the priority for recall-
ing and removing a scene of
type Sun protection for the
channel.

Activate sun protection switch-
ing state

On, Off
Basic setting: On

Defines the behaviour of the
output on deactivating the sun
protection. Only visible when
the priority for the sun protec-
tion is 0.

Deactivate sun protection
switching state

On, Off
Basic setting: Off

Defines the behaviour of the
output on deactivating the sun
protection. Only visible when
the priority for the sun protec-
tion is 0.

Priority, twilight

0...4
Basic setting: 0

Specifies the priority for recall-
ing and removing a scene of
type Twilight for the channel.

Activate twilight switching
state

On, Off
Basic setting: On

Defines the behaviour of the
output on activating the twi-
light function.

Deactivate twilight switching
state

On, Off
Basic setting: Off

Defines the behaviour of the
output on deactivating the twi-
light function. Only visible
when the priority for the twi-
light function is 0.

Switch off brightness over-
shoot

On, Off
Basic setting: On

Allows automatic switch-off
according to the brightness. If
the parameter is On, then the
light controller switches off
automatically when the bright-
ness setpoint is greatly ex-
ceeded. This parameter is not
yet active, as a light controller
has not yet been implemen-
ted.

Switch on brightness under-
shoot

On, Off
Basic setting: Off

Allows automatic switch-on
according to the brightness. If
the parameter is On, then the
light controller switches on
automatically when the bright-
ness setpoint is greatly under-
shot. We recommend only us-
ing the parameter in connec-
tion with the parameter
"Switch-off on brightness over-
shoot". This parameter is not

9 / 10

82592223

15.12.2020

J0082592223

Summary of Contents for FMAS10ZS











Reviews: