Jung KNX 390011 SU Quick Start Manual Download | Manualshive

Page: 10 / 10

background image

Universal dimming actuator, 1-gang

Installation or commissioning error. Disconnect device and luminaire, switch off circuit
breaker.
Check installation and correct.
If the wrong dimming principle has been preselected: Set correct dimming principle.
If dimming actuator calibrates itself incorrectly, e.g. with highly inductive mains or long
load cables: preselect correct dimming principle with commissioning.

LED lamp is dimly lit when dimmer is switched off

Cause: LED lamp is not optimally suited for this dimmer.

Use a compensation module, see accessories.
Use another type of LED lamp or an LED lamp of another manufacturer.

7

Accessories

External sensor

Condensation sensor

Leakage sensor

8

Warranty

The warranty is provided in accordance with statutory requirements via the specialist trade.

ALBRECHT JUNG GMBH & CO. KG
Volmestraße 1
58579 Schalksmühle
GERMANY

Telefon: +49 2355 806-0
Telefax: +49 2355 806-204
kundencenter@jung.de
www.jung.de

10 / 10

82404403

02.02.2021

J0082404403

«
...
8
9
10

Summary of Contents for KNX 390011 SU











Reviews:

No comments

Related manuals for KNX 390011 SU

Brand: GE Pages: 8

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 12

Brand: Danfoss Pages: 24

Brand: Danfoss Pages: 60

Brand: Danfoss Pages: 10

Brand: Danfoss Pages: 20

Brand: Lawler Pages: 6

Brand: Data Aire Pages: 28

Z3-DM8107-SDI-RPS

Brand: Z3 Technology Pages: 73

Brand: Z-Wave Pages: 14

Brand: Z-Wave.Me Pages: 4

Brand: Ascon tecnologic Pages: 16

Brand: KIOUR Pages: 3

Brand: Topway Pages: 14

Brand: Wave Home Solutions Pages: 15

Travel About Series

Brand: Kolcraft Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands