F 5
0
509
.GB
Maintenance Intervals
Standard
=
t
W A B C
Hydraulic oper-
ations
6.1 Check cylinders and piston rods for damage
and leaks, and make sure they are secure.
t
6.2 Check settings and wear levels of slide pieces
and stops, and adjust if necessary
t
6.3 Check load chain setting and tension if necessary
t
6.4 Visually inspect mast rollers and check contact
surface wear level
t
6.5 Check lateral clearance of mast connections
and of fork carriage
t
6.6 Test the hydraulic system.
t
6.7 Replace the hydraulic oil filter
t
6.8 Check that hose and pipe lines and their connections
are secure, check for leaks and damage
t
6.9 Test the emergency lowering
t
6.10 Check hydraulic oil level and top up if necessary.
t
6.11 Replace the hydraulic oil after 2000 service hours / bi-
annually
t
6.12 Check forks, load handler [e.g. mandrel] for wear
and damage
t
Agreed per-
formance
levels
7.1 Carry out a test run with rated load
t
7.2 Demonstration after servicing
t
7.3 Lubricate truck in accordance with Lubrication
Schedule.
t
Steering
8.1 Test tiller recuperating function
t
Charger
9.1 Check mains connector and mains cable.
t
9.2 Check the start-up protection system for trucks
with an on-board charger.
t
9.3 Potential measurement on chassis while charging
is in progress.
t
F 5
0
509
.GB
Maintenance Intervals
Standard
=
t
W A B C
Hydraulic oper-
ations
6.1 Check cylinders and piston rods for damage
and leaks, and make sure they are secure.
t
6.2 Check settings and wear levels of slide pieces
and stops, and adjust if necessary
t
6.3 Check load chain setting and tension if necessary
t
6.4 Visually inspect mast rollers and check contact
surface wear level
t
6.5 Check lateral clearance of mast connections
and of fork carriage
t
6.6 Test the hydraulic system.
t
6.7 Replace the hydraulic oil filter
t
6.8 Check that hose and pipe lines and their connections
are secure, check for leaks and damage
t
6.9 Test the emergency lowering
t
6.10 Check hydraulic oil level and top up if necessary.
t
6.11 Replace the hydraulic oil after 2000 service hours / bi-
annually
t
6.12 Check forks, load handler [e.g. mandrel] for wear
and damage
t
Agreed per-
formance
levels
7.1 Carry out a test run with rated load
t
7.2 Demonstration after servicing
t
7.3 Lubricate truck in accordance with Lubrication
Schedule.
t
Steering
8.1 Test tiller recuperating function
t
Charger
9.1 Check mains connector and mains cable.
t
9.2 Check the start-up protection system for trucks
with an on-board charger.
t
9.3 Potential measurement on chassis while charging
is in progress.
t
Summary of Contents for EJC M10
