F 1
0708
.GB
F Maintenance of the forklift truck
1
Operational safety and environmental protection
The checks and servicing operations contained in this chapter must be performed in
accordance with the intervals as indicated in the servicing checklists.
F
Modifications to the forklift truck, especially to the safety devices, are not permitted.
The operational speeds of the truck must not be changed under any circumstances.
M
Only original spare parts come under the remit of our quality assurance service. To
ensure safe and reliable operation of the forklift truck, only use the manufacturer’s
spare parts. Used parts, oils and fuels must be disposed of in accordance with the
applicable environmental protection regulations. For oil changes, contact the
manufacturer’s oil service department.
Upon completion of inspection and servicing, carry out the tasks contained in the
„Recommissioning“ section (see Chapter
F).
2
Maintenance Safety Regulations
Maintenance personnel:
The forklift truck must only be serviced and maintained by
trained personnel provided by the manufacturer. The manufacturer’s service
department has specially trained field engineers for this work. We therefore
recommend a maintenance contract with the manufacturer’s local service centre.
Lifting and jacking up:
When a forklift truck is to be lifted, the lifting gear must only
be secured to the points specially provided for this purpose. When the truck is to be
jacked up, take appropriate measures to prevent the truck from slipping or tipping
over (e.g. wedges, wooden blocks). Only work under a raised load handler and cab
if they are secured by a chain of sufficient capacity or by the retaining bolt (see “Se-
curing the Driver's Position Carriage” in Chapter F).
Z
Jacking point see chapter B.
Cleaning:
No inflammable liquids may be used to clean the forklift truck. Prior to
cleaning, all safety measures required to prevent sparking (e.g. through short circuits)
must be taken. For battery-operated trucks, the battery connector must be removed.
Only weak suction or compressed air and non-conductive antistatic brushes may be
used for cleaning electrical or electronic assemblies.
M
If the truck is to be cleaned with a water jet or a high-pressure cleaner, all electrical
and electronic components must be carefully covered beforehand as moisture can
cause malfuntions.
Do not clean with steam jets.
After cleaning, carry out the tasks detailed in the „Recommissioning“ section.
F 1
0708
.GB
F Maintenance of the forklift truck
1
Operational safety and environmental protection
The checks and servicing operations contained in this chapter must be performed in
accordance with the intervals as indicated in the servicing checklists.
F
Modifications to the forklift truck, especially to the safety devices, are not permitted.
The operational speeds of the truck must not be changed under any circumstances.
M
Only original spare parts come under the remit of our quality assurance service. To
ensure safe and reliable operation of the forklift truck, only use the manufacturer’s
spare parts. Used parts, oils and fuels must be disposed of in accordance with the
applicable environmental protection regulations. For oil changes, contact the
manufacturer’s oil service department.
Upon completion of inspection and servicing, carry out the tasks contained in the
„Recommissioning“ section (see Chapter
F).
2
Maintenance Safety Regulations
Maintenance personnel:
The forklift truck must only be serviced and maintained by
trained personnel provided by the manufacturer. The manufacturer’s service
department has specially trained field engineers for this work. We therefore
recommend a maintenance contract with the manufacturer’s local service centre.
Lifting and jacking up:
When a forklift truck is to be lifted, the lifting gear must only
be secured to the points specially provided for this purpose. When the truck is to be
jacked up, take appropriate measures to prevent the truck from slipping or tipping
over (e.g. wedges, wooden blocks). Only work under a raised load handler and cab
if they are secured by a chain of sufficient capacity or by the retaining bolt (see “Se-
curing the Driver's Position Carriage” in Chapter F).
Z
Jacking point see chapter B.
Cleaning:
No inflammable liquids may be used to clean the forklift truck. Prior to
cleaning, all safety measures required to prevent sparking (e.g. through short circuits)
must be taken. For battery-operated trucks, the battery connector must be removed.
Only weak suction or compressed air and non-conductive antistatic brushes may be
used for cleaning electrical or electronic assemblies.
M
If the truck is to be cleaned with a water jet or a high-pressure cleaner, all electrical
and electronic components must be carefully covered beforehand as moisture can
cause malfuntions.
Do not clean with steam jets.
After cleaning, carry out the tasks detailed in the „Recommissioning“ section.
Summary of Contents for EKS 310
