E 37
501
1
838
6 GB
Depending on the parameter settings there are different operating methods to reach
the desired height:
If another shelf is selected during the positioning process, this value is stored in a
buffer and shown for approx. one second in the display. When the stacking cycle is
finished the shelf is automatically retrieved from the buffer.
Depending on the variant the following variations are possible for the stacking cycle:
1. Stacking cycle not active.
2. Stacking and retrieving is predefined by the load sensor. The individual functions
such as traversing, lifting, and lowering are performed by the driver.
After reaching the respective end position the next work step can be carried out.
3. During the entire stacking cycle the hydraulic control knob must be pushed.
Neither traversing or lifting nor the lowering speed can be influenced by the
driver.
If the hydraulic control knob is no longer pushed, the work cycle is cancelled.
4. It is only necessary to push the hydraulic control knob during traversing of the
fork carrier, after that the stacking cycle runs automatically until it is completed.
5. It is only necessary to push the hydraulic control knob briefly, the subsequent
work cycle will run automatically (it starts when the pushbutton is released).
6. It is necessary to push the hydraulic control knob for starting the individual work
cycles.
Except for operating mode 1 the driver cannot influence the working speed and
functions.
A
All automatic cycles can be interrupted by stepping on the foot switch.
f
In case of danger actuate the EMERGENCY OFF switch.
OFF
No desired height set (desired height must approached
manually).
manual
The hydraulic control knob must be actuated as long
until the desired height is reached.
semi-automatic
The hydraulic control knob must be actuated until
shortly before reaching the desired height.
automatic
The hydraulic control knob must be tapped into the
desired direction, the desired height is then
automatically approached.
E 37
501
1
838
6 GB
Depending on the parameter settings there are different operating methods to reach
the desired height:
If another shelf is selected during the positioning process, this value is stored in a
buffer and shown for approx. one second in the display. When the stacking cycle is
finished the shelf is automatically retrieved from the buffer.
Depending on the variant the following variations are possible for the stacking cycle:
1. Stacking cycle not active.
2. Stacking and retrieving is predefined by the load sensor. The individual functions
such as traversing, lifting, and lowering are performed by the driver.
After reaching the respective end position the next work step can be carried out.
3. During the entire stacking cycle the hydraulic control knob must be pushed.
Neither traversing or lifting nor the lowering speed can be influenced by the
driver.
If the hydraulic control knob is no longer pushed, the work cycle is cancelled.
4. It is only necessary to push the hydraulic control knob during traversing of the
fork carrier, after that the stacking cycle runs automatically until it is completed.
5. It is only necessary to push the hydraulic control knob briefly, the subsequent
work cycle will run automatically (it starts when the pushbutton is released).
6. It is necessary to push the hydraulic control knob for starting the individual work
cycles.
Except for operating mode 1 the driver cannot influence the working speed and
functions.
A
All automatic cycles can be interrupted by stepping on the foot switch.
f
In case of danger actuate the EMERGENCY OFF switch.
OFF
No desired height set (desired height must approached
manually).
manual
The hydraulic control knob must be actuated as long
until the desired height is reached.
semi-automatic
The hydraulic control knob must be actuated until
shortly before reaching the desired height.
automatic
The hydraulic control knob must be tapped into the
desired direction, the desired height is then
automatically approached.
Summary of Contents for ETX ac 125
