F 11
501
1
838
6 GB
6.4
Inspection of lifting chains
Improper wear and external damages:
According to the official regulations a chain is regarded as worn out, if it has elongated
by more than 3% in the section where it runs around the deflection pulley. For safety
reason we recommend to replace a chain when it has elongated by 2%.
A chain should also be changed immediately when external damages are detected,
as such damages result in fatigue fractures after a certain time period.
m
If the industrial truck is equipped with two lifting chains, always both chains must be
replaced. Only then the equal load distribution to both chains can be guaranteed.
When replacing chains, also the connection bolts between chain anchor and chain
must be renewed. As a rule, only original parts may be used.
6.5
Chain repair
Also when repairing chains, only original parts may be used. The rivet heads must be
ground off before dismounting. In this way damages caused by driving the bolt
through the intermediate plate resp. the inner link in the hole section are avoided.
Removed bolts and plates must not be reused.
6.6
Changing gear oil
m
Absolute care must be taken that the oil cannot be spilled into the sewer or onto the
soil. Waste oil must be securely stored until its proper disposal.
Draining the oil:
– Place an oil pan under the
transmission.
– Open oil drain plug (7) on the bottom
side of the transmission and allow the
oil to drain.
Refilling oil:
– Screw in oil drain plug (7) and tighten.
– Open oil check and filler plug (6) at the
top side of the transmission.
– Fill new transmission oil up to the oil
check opening.
– Screw in oil check and filler plug (6).
A
Because of the proper disposal and
possibly required special tools and skills
the transmission and hydraulic oil
change as well as changing brake fluid and filters should be performed by the
customer service.
6
7
F 11
501
1
838
6 GB
6.4
Inspection of lifting chains
Improper wear and external damages:
According to the official regulations a chain is regarded as worn out, if it has elongated
by more than 3% in the section where it runs around the deflection pulley. For safety
reason we recommend to replace a chain when it has elongated by 2%.
A chain should also be changed immediately when external damages are detected,
as such damages result in fatigue fractures after a certain time period.
m
If the industrial truck is equipped with two lifting chains, always both chains must be
replaced. Only then the equal load distribution to both chains can be guaranteed.
When replacing chains, also the connection bolts between chain anchor and chain
must be renewed. As a rule, only original parts may be used.
6.5
Chain repair
Also when repairing chains, only original parts may be used. The rivet heads must be
ground off before dismounting. In this way damages caused by driving the bolt
through the intermediate plate resp. the inner link in the hole section are avoided.
Removed bolts and plates must not be reused.
6.6
Changing gear oil
m
Absolute care must be taken that the oil cannot be spilled into the sewer or onto the
soil. Waste oil must be securely stored until its proper disposal.
Draining the oil:
– Place an oil pan under the
transmission.
– Open oil drain plug (7) on the bottom
side of the transmission and allow the
oil to drain.
Refilling oil:
– Screw in oil drain plug (7) and tighten.
– Open oil check and filler plug (6) at the
top side of the transmission.
– Fill new transmission oil up to the oil
check opening.
– Screw in oil check and filler plug (6).
A
Because of the proper disposal and
possibly required special tools and skills
the transmission and hydraulic oil
change as well as changing brake fluid and filters should be performed by the
customer service.
6
7
Summary of Contents for ETX ac 125
