Table 469: show mpls lsp Output Fields
(continued)
Level of Output
Field Description
Field Name
brief
Number of active routes (prefixes) installed in the routing table. For ingress
RSVP sessions, the routing table is the primary IPv4 table (
inet.0
). For transit
and egress RSVP sessions, the routing table is the primary MPLS table (mpls.0).
Rt
detail extensive
(Ingress LSP) Name of the active path:
Primary
or
Secondary
.
ActivePath
detail
Fast reroute has been requested by the ingress routing device.
FastReroute
desired
detail
Link protection has been requested by the ingress routing device.
Link protection
desired
detail extensive
(Ingress LSP) CSPF load-balancing rule that was configured to select the LSP's
path among equal-cost paths
: Most-fill
,
Least-fill
, or
Random
.
LoadBalance
All levels
Signal type for GMPLS LSPs. The signal type determines the peak data rate for
the LSP:
DS0
,
DS3
,
STS-1
,
STM-1
, or
STM-4
.
Signal type
All levels
LSP encoding type:
Packet
,
Ethernet
,
PDH
,
SDH/SONET
,
Lambda
, or
Fiber
.
Encoding type
All levels
Type of switching on the links needed for the LSP:
Fiber
,
Lamda
,
Packet
,
TDM
,
or
PSC-1
.
Switching type
All levels
Generalized Payload Identifier (identifier of the payload carried by an LSP):
HDLC
,
Ethernet
,
IPv4
,
PPP
, or
Unknown
.
GPID
All levels
Configured protection capability desired for the LSP:
Extra
,
Enhanced
,
none
,
One plus one
,
One to one
, or
Shared
.
Protection
All levels
(Bidirectional LSPs) Incoming label for reverse direction traffic for this LSP.
Upstream label in
All levels
(Bidirectional LSPs) Outgoing label for reverse direction traffic for this LSP.
Upstream label out
All levels
(Bidirectional LSPs) Label the upstream node suggests to use in the Resv
message that is sent.
Suggested label
received
All levels
(Bidirectional LSPs) Label the downstream node suggests to use in the Resv
message that is returned.
Suggested label
sent
detail extensive
(Ingress LSP) The LSP is performing autobandwidth allocation.
Autobandwidth
detail extensive
(Ingress LSP) Configured minimum value of the LSP, in bps.
MinBW
detail extensive
(Ingress LSP) Configured maximum value of the LSP, in bps.
MaxBW
detail extensive
(Ingress LSP) Configured value of the bandwidth adjustment timer, indicating
the total amount of time allowed before bandwidth adjustment will take place,
in seconds.
AdjustTimer
Copyright © 2010, Juniper Networks, Inc.
3486
Complete Software Guide for Junos
®
OS for EX Series Ethernet Switches, Release 10.3
Summary of Contents for JUNOS OS 10.3 - SOFTWARE
