Juniper JUNOS OS 10.3 - SOFTWARE Manual Download | Manualshive

Page: 749 / 3946

background image

Various conditions related to the chassis components trigger yellow and red alarms. You
cannot configure these conditions. See “Understanding Alarm Types and Severity Levels
on EX Series Switches” on page 637.

Action

You can monitor chassis alarms by watching the ALM chassis status LED and using the
LCD panel to gather information about the alarm. See Chassis Status LEDs in an EX8200
Switch and LCD Panel in an EX8200 Switch.

To display switch chassis alarms in the CLI, use the following command

user@host>

show chassis alarms

The command output displays the number of alarms currently active, the time when the
alarm began, the severity level, and an alarm description. Note the date and time of an
alarm so that you can correlate it with error messages in the messages system log file.

You can also monitor chassis alarms using the J-Web interface. See “Checking Active
Alarms with the J-Web Interface” on page 652.

Table 122 on page 653 lists some of the chassis alarms that an EX8200 switch can generate.

Table 122: Chassis Alarms for EX8200 Switches

Additional Information

Severity

Remedy

Alarm Condition

Component

The switch will eventually get too
hot to operate if a fan tray is
removed. Temperature alarms will
follow.

This alarm is expected during fan
tray removal and installation.

Yellow/Red

Install the fan tray.

The fan tray has been
removed from the
chassis.

Fan tray

Individual fans cannot be
replaced; you must replace the
fan tray.

Red

Replace the fan tray.

One or more fans in a
fan tray is spinning
below the required
speed.

Fan tray

The switch will eventually get too
hot to operate if a fan tray is not
operating. Temperature alarms
will follow.

Red

Remove and reinsert
the fan tray.

If removing and
reinserting the fan tray
does not resolve the
problem, reboot the
switch.

The fan tray’s internal
connection to the
switch is not
functioning properly.

Fan tray

653

Copyright © 2010, Juniper Networks, Inc.

Chapter 40: Administering and Monitoring System Functions

«
...
747
748
749
750
751
...
»

Summary of Contents for JUNOS OS 10.3 - SOFTWARE











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JUNOS OS 10.3 - SOFTWARE

COLDFUSION MX 61-CFML

Brand: MACROMEDIA Pages: 34

ExtremeWare 7.0.0

Brand: Extreme Networks Pages: 1598

Brand: Kenwood Pages: 21

Brand: Kenwood Pages: 40

Brand: Kenwood Pages: 52

Brand: Kenwood Pages: 68

PTF100NTU - LCD PROJECTOR

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 10

Media Manager V2.1

Brand: Panasonic Pages: 28

Lumix VQT0U14 ( )

Brand: Panasonic Pages: 36

Brand: Panasonic Pages: 70

PANATERM Ver. 3.7

Brand: Panasonic Pages: 78

Voice Editing Ver.2.0

Brand: Panasonic Pages: 132

Brand: Panasonic Pages: 156

SyncMaster S23A950D

Brand: Samsung Pages: 90

SyncMaster T23A750

Brand: Samsung Pages: 292

Brand: Billion Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands