background image

Step 6: Configure the JA2500 Appliance

You can configure a JA2500 Appliance as a Junos Space node or as a specialized node
used for fault monitoring and performance monitoring (FMPM).

Before you begin, ensure that you have the relevant information (depending on whether
you are configuring a Junos Space node or an FMPM node) shown in

Table 2 on page 17

available:

Table 2: Information Required for Junos Space Appliance Configuration

Required for Configuring FMPM
Node?

Required for Configuring Junos
Space Node?

Description

Yes

Yes

IP address and subnet mask or prefix of the eth0
interface

Yes

Yes

IP address of the default gateway

Yes

Yes

IP address of the name server

Yes, only if you are configuring the
eth1 interface

Yes, only if you are configuring the
eth1 interface

IP address and subnet mask of the eth1 interface

NOTE:

From Junos Space Network Management

Platform Release 14.1R1 onward, you can
configure the eth1 Ethernet interface as an
administrative interface.

Yes, only if the IP address of the eth1
interface is not in the same subnet
as the VIP address

Yes, only if the IP address for the eth1
interface is not in the same subnet
as the VIP address

IP address of the default gateway for the eth1
interface

No

Yes, only if you are configuring the
eth3 interface

IP address and subnet mask or prefix of the eth3
interface

No

Yes, only if you are configuring the
eth3 interface

IP address of the default gateway for the eth3
interface

Yes

NOTE:

This is the VIP address of the

FMPM nodes and is used for
communications between Junos
Space nodes and FMPM nodes. This
VIP address must be different from
the VIP address used to access the
Web GUI.

Yes

NOTE:

The VIP address is used to

access the Junos Space Network
Management Platform GUI through
a Web browser.

Virtual IP (VIP) address

NOTE:

The VIP address must be in the same

subnet as the IP address assigned to the eth0
interface.

Yes

Yes

NTP server settings with which the Junos Space
Appliance synchronizes its time.

17

Copyright © 2018, Juniper Networks, Inc.

Step 6: Configure the JA2500 Appliance

Summary of Contents for Junos Space JA2500






























Reviews: