no Negate a command or set its default(s)
peak-burst Set the peak burst size in Bytes
peak-rate Set the peak access rate in bits per second
run Run an exec mode command (alias command do)
sleep Make the Command Interface pause for a specified duration
Redundancy Configuration Mode
In this mode, you can activate high availability (SRP switchover) by issuing the
mode
high-availability
command.
From Global Configuration mode, type the
redundancy
command and press Enter.
host1(config-router)#
redundancy
host1(config-redundancy)#
?
default Set a command to its default(s)
do Run an exec mode command (alias command run)
exit Exit from the current command mode
help Describe the interactive help system
log Configure logging settings
macro Run a CLI macro
mode Configure redundancy mode
no Negate a command or set its default(s)
run Run an exec mode command (alias command do)
sleep Make the Command Interface pause for a specified duration
Remote Neighbor Configuration Mode
In this mode, you can configure remote neighbor parameters for Routing Information
Protocol (RIP), Protocol Independent Multicast (PIM), and Open Shortest Path First
(OSPF).
From Global Configuration mode, type either
router rip, router pim,
or
router ospf
and
the
processID
. Press Enter. You are now in Router Configuration mode.
From Router Configuration mode, type the
remote-neighbor
command and the
appropriate attributes, and press Enter.
host1(config-router)#
remote-neighbor 10.13.5.61
host1(config-router-rn)#
?
authentication Configure authentication
default Set a command to its default(s)
distribute-list Specify an access list to be a distribute list
do Run an exec mode command (alias command run)
exit Exit from the current command mode
exit-remote-neighbor Exit the remote-neighbor configuration mode
help Describe the interactive help system
log Configure logging settings
macro Run a CLI macro
no Negate a command or set its default(s)
receive Set reception characteristics
route-map Specify a route map to apply to outgoing routes
run Run an exec mode command (alias command do)
send Set transmit characteristics
sleep Make the Command Interface pause for a specified
duration
split-horizon Enable Split-horizon
time-to-live Configure ttl used to send to this neighbor
update-source Source address to be used for transmit
107
Copyright © 2010, Juniper Networks, Inc.
Chapter 2: Command-Line Interface
Summary of Contents for JUNOSE 11.3
