Juniper SRX240 Series Hardware Manual Download

Page: 47 / 198

CHAPTER 6

Planning and Preparing the Site

•

Site Preparation Checklist for the SRX240 Services Gateway on page 29

•

General Site Guidelines for Installing the SRX240 Services Gateway on page 30

•

SRX240 Services Gateway Chassis on page 31

•

SRX240 Services Gateway Rack Requirements on page 33

•

Clearance Requirements for Airflow and Hardware Maintenance on the SRX240 Services
Gateway on page 33

Site Preparation Checklist for the SRX240 Services Gateway

The checklist in

Table 14 on page 29

summarizes the tasks you need to perform when

preparing a site for installing the SRX240 Services Gateway.

Table 14: Site Preparation Checklist for Services Gateway Installation

Date
and
Notes

Additional Information

Item or Task

Environment

“SRX240 Services Gateway Chassis”
on page 31

Verify that environmental factors such as
temperature and humidity do not exceed
device tolerances.

Power

“SRX240 Services Gateway Electrical
and Power Requirements” on page 36

Measure distance between external power
sources and device installation site.

“SRX240 Services Gateway Grounding
Specifications” on page 59

Locate sites for connection of system
grounding.

“SRX240 Services Gateway AC Power
Specifications and Requirements” on
page 37

Gather the AC power requirements.

“SRX240 Services Gateway DC Power
Specifications and Requirements” on
page 38

Gather the DC power requirements.

Summary of Contents for SRX240 Series










































































































































































Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands

Juniper SRX240 Series, Hardware Manual

Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands