Juniper SRX240 Series Hardware Manual Download

Page: 60 / 198

Table 24: RJ-45 Connector Pinouts for the Services Gateway Ethernet
Port (10/100 Mbps)

Signal

TX+

TX-

RX+

Termination network

RX-

Termination network

Table 25 on page 42

describes the RJ-45 connector pinouts for the Ethernet port for 1

Gbps (1000 Mbps).

Table 25: RJ-45 Connector Pinouts for the Services Gateway Ethernet
Port (1 Gbps)

Signal

BI_DA+

BI_DA-

BI_DB+

BI_DC+

BI_DC-

BI_DB-

BI_DD+

BI_DD-

Documentation

Interface Cable and Wire Specifications for the SRX240 Services Gateway on page 41

•

RJ-45 Connector Pinouts for the SRX240 Services Gateway Console Port on page 43

SRX240 Services Gateway Hardware Guide

Summary of Contents for SRX240 Series










































































































































































Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands

Juniper SRX240 Series, Hardware Manual

Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands