Juniper SRX240 Series Hardware Manual Download

Page: 83 / 198

Disable flow control by entering

AT&K0

Save modem settings by entering

AT&W

Documentation

Connecting to the SRX240 Services Gateway Setup Wizard on page 83

•

Connecting the SRX240 Services Gateway to the CLI on page 85

•

Connecting to the CLI at the User End for the SRX240 Services Gateway on page 66

•

Connecting the Modem to the Console Port on the SRX240 Services Gateway on
page 65

Connecting the Modem to the Console Port on the SRX240 Services Gateway

To connect the dial-up modem to the console port on the services gateway:

Turn off power to the services gateway.

Turn off power to the modem.

Plug one end of the Ethernet cable supplied with your services gateway into the
console port.

Plug the other end of the CAT-5e (Ethernet cable) into the RJ-45 to DB-9 serial port
adapter supplied with your services gateway.

Connect the serial port adapter to a separately purchased DB-9 female to DB-25
male adapter or other adapter appropriate for your modem.

Plug the modem adapter into the DB-25 connector on the modem.

Connect the modem to your telephone network.

Turn on the power to the modem.

Power on the services gateway by pressing the Power button on the front panel. Verify
that the Power LED on the front panel turns green.

NOTE:

Most modems have an RS-232 DB-25 connector. You must

separately purchase an adapter to connect your modem to the RJ-45 to
DB-9 adapter and Ethernet cable supplied with the services gateway.

Documentation

Connecting to the SRX240 Services Gateway Setup Wizard on page 83

•

Connecting the SRX240 Services Gateway to the CLI on page 85

•

Connecting the Modem at the SRX240 Services Gateway End on page 64

•

Connecting to the CLI at the User End for the SRX240 Services Gateway on page 66

Chapter 13: Connecting the SRX240 Services Gateway to External Devices

Summary of Contents for SRX240 Series










































































































































































Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands

Juniper SRX240 Series, Hardware Manual

Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands