Juniper SRX240 Series Hardware Manual Download

Page: 90 / 198

Figure 16: DC Power Feed on SRX240 Services Gateway with DC Power
Supply Model

g037544

Terminal
block cover

Terminal block

LEDs

Remove the screws on the terminals using the Phillips (+) screwdriver, number 1. Save
the screws.

WARNING:

Ensure that the power cables do not block access to the device

or drape where people can trip on them.

Connect the power feed to the power sources as shown in

Figure 17 on page 73

. Secure

power source cables to the power feed on the device by screwing the ring lugs attached
to the cables to the appropriate terminals by using the screw from the terminals.

SRX240 Services Gateway Hardware Guide

Summary of Contents for SRX240 Series










































































































































































Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands

Juniper SRX240 Series, Hardware Manual

Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands