Juniper SRX240 Series Hardware Manual Download

Page: 105 / 198

Table 37: Port Settings When Connecting the Services Gateway to the
CLI Locally

Value

Port Settings

9600

Bits per second

Data bits

None

Parity

Stop bits

None

Flow control

Power on the services gateway by pressing the Power button on the front panel. Verify
that the Power LED on the front panel turns green.

The terminal emulation screen on your management device displays the startup
sequence. When the services gateway has finished starting up, a login prompt appears.

10.

root

. No password is required at initial connection, but you must

assign a root password before committing any configuration settings.

Connecting a Services Gateway to the CLI Remotely

You can connect the services gateway to the CLI from a remote location through two
dial-up modems:

•

A modem that is connected to the console port on the services gateway

•

A second modem connected to a remote management device

The modem connection allows you to remotely perform the same console operations
you can perform locally.

Documentation

Connecting to the SRX240 Services Gateway Setup Wizard on page 83

•

Connecting to the CLI at the User End for the SRX240 Services Gateway on page 66

•

Connecting the Modem at the SRX240 Services Gateway End on page 64

•

Connecting the Modem to the Console Port on the SRX240 Services Gateway on
page 65

Viewing Factory Default Settings of the SRX240 Services Gateway

To view the factory-default configuration of the branch SRX Series Services Gateway
using the CLI:

Verify that the services gateway is powered on.

Chapter 15: Performing Initial Configuration

Summary of Contents for SRX240 Series










































































































































































Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands

Juniper SRX240 Series, Hardware Manual

Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands