Juniper SRX240 Series Hardware Manual Download

Page: 187 / 198

CHAPTER 26

Agency Approvals and Regulatory
Compliance Information

•

SRX240 Services Gateway Agency Approvals on page 169

•

SRX240 Services Gateway Compliance Statements for EMC Requirements on page 170

•

SRX240 Services Gateway (DC Power Supply Model) Compliance Statements for
Network Equipment Building System (NEBS) on page 172

•

SRX240 Services Gateway Compliance Statements for Environmental
Requirements on page 172

•

SRX240 Services Gateway Compliance Statements for Acoustic Noise on page 172

SRX240 Services Gateway Agency Approvals

The services gateway complies with the following standards:

•

Safety

•

CAN/CSA-C22.2 No. 60950-1 (2007) Information Technology Equipment

•

UL 60950-1 (2nd Edition) Information Technology Equipment

•

EN 60950-1 (2005) Information Technology Equipment

•

IEC 60950-1 (2005) Information Technology Equipment

•

EN 60825-1 +A1+A2 (1994) Safety of Laser Products - Part 1: Equipment Classification

•

EMC

•

EN 300 386 V1.3.3 (2005) Telecom Network Equipment - EMC requirements

•

EMI

•

FCC Part 15 Class A (2007) USA Radiated Emissions

•

EN 55022 Class A (2006) European Radiated Emissions

•

VCCI Class A (2007) Japanese Radiated Emissions

169

Summary of Contents for SRX240 Series










































































































































































Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands

Juniper SRX240 Series, Hardware Manual

Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands