Juniper SRX240 Series Hardware Manual Download

Page: 33 / 198

SRX240 Services Gateway Back Panel (AC power supply models)

Figure 3 on page 15

shows the back panel of the SRX240 Services Gateway AC power

supply models.

Figure 3: SRX240 Services Gateway Back Panel ( with AC Power Supply
Models)

g037502

Table 7 on page 15

lists the back panel components of the SRX240 Services Gateway

AC power supply models.

Table 7: SRX240 Services Gateway Back Panel AC Power Supply Models

Component

Number

Cable tie holder

Power supply point

Grounding point

Air filter slot

NOTE:

The air filter is shipped with SRX240 Services Gateways with DC

power supply models only.

You can order the air filter separately for the SRX240 Services Gateway with
AC power supply models. Contact your Juniper Networks customer service
representative for more information.

SRX240 Services Gateway Back Panel (DC Power Supply Model)

Figure 4 on page 15

shows the back panel of an SRX240 Services Gateway with DC power

supply models.

Figure 4: SRX240 Services Gateway DC Power Supply Model

g037538

Table 8 on page 16

lists the back panel components of the SRX240 Services Gateway

DC power supply models.

Chapter 3: Chassis Description

Summary of Contents for SRX240 Series










































































































































































Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands

Juniper SRX240 Series, Hardware Manual

Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands