Juniper SRX240 Series Hardware Manual Download

Page: 38 / 198

Ethernet Port LEDs

On the SRX240 Services Gateway, each Gigabit Ethernet port has the two LEDs as shown
in

Figure 6 on page 20

Figure 6: SRX240 Services Gateway Port LEDs

g037504

Table 11: SRX240 Services Gateway Port LEDs

LED

Number

TX/RX/Link LED

PoE (Power over Ethernet) LED

NOTE:

The PoE LED is enabled only on the PoE variant of the SRX240 Services

Gateway. For non-PoE services gateways, the PoE LED remains off.

Table 12 on page 20

describes the Ethernet port LEDs.

Table 12: SRX240 Services Gateway Ethernet Port LEDs

Description

State

Color

Function

Link is active. Data
communication is
taking place.

Blinking

Green

TX/RX/Link

Link is active. No data
communication is
taking place.

Steady

Link is inactive.

Off

Unlit

SRX240 Services Gateway Hardware Guide

Summary of Contents for SRX240 Series










































































































































































Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands

Juniper SRX240 Series, Hardware Manual

Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands