Juniper SRX240 Series Hardware Manual Download

Page: 53 / 198

CHAPTER 7

Power Requirements and Specifications

•

SRX240 Services Gateway Site Electrical Wiring Guidelines on page 35

•

SRX240 Services Gateway Electrical and Power Requirements on page 36

•

SRX240 Services Gateway AC Power Specifications and Requirements on page 37

•

SRX240 Services Gateway DC Power Specifications and Requirements on page 38

SRX240 Services Gateway Site Electrical Wiring Guidelines

Table 18 on page 35

describes the factors you must consider while planning the electrical

wiring for the services gateway at your site.

CAUTION:

It is particularly important to provide a properly grounded and

shielded environment and to use electrical surge-suppression devices.

CAUTION:

For devices with AC power supplies, an external surge protective

device (SPD) must be used at the AC power source.

Table 18: Site Electrical Wiring Guidelines for the Services Gateway

Guideline

Site Wiring Factor

To ensure that signaling functions optimally:

•

Install wires correctly.

Improperly installed wires can emit radio interference.

•

Do not exceed the recommended distances or pass wires
between buildings.

The potential for damage from lightning strikes increases if wires
exceed recommended distances or if wires pass between
buildings.

•

Shield all conductors.

The electromagnetic pulse (EMP) caused by lightning can
damage unshielded conductors and destroy electronic devices.

Signaling Limitations

Summary of Contents for SRX240 Series










































































































































































Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands

Juniper SRX240 Series, Hardware Manual

Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands