Juniper SRX240 Series Hardware Manual Download

Page: 55 / 198

•

SRX240 Services Gateway Rack Requirements on page 33

•

Clearance Requirements for Airflow and Hardware Maintenance on the SRX240 Services
Gateway on page 33

SRX240 Services Gateway AC Power Specifications and Requirements

This topic includes the following sections:

•

AC Power Requirement Specifications on page 37

•

AC Power Cord Specifications on page 37

AC Power Requirement Specifications

The AC power system electrical specifications for the SRX240 Services Gateway are
listed in

Table 19 on page 37

Table 19: AC Power Supply Specifications for the SRX240 Services
Gateway

Specification

Power Requirement

100 to 240 VAC

AC input voltage

50 to 60 Hz

AC input line frequency

2.5 A

4.5 A (for PoE models)

AC system current rating

AC Power Cord Specifications

Table 20 on page 37

depicts the plugs on the AC power cords provided for each country

or region.

Table 20: AC Power Cord Specifications

Model Number

Country

CBL-JX-PWR-AU

Australia

CBL-JX-PWR-CH

China

CBL-JX-PWR-EU

Europe (except Denmark, Italy, Switzerland,
and United Kingdom)

CBL-JX-PWR-IT

Italy

CBL-JX-PWR-JP

Japan

CBL-JX-PWR-US

North America

Chapter 7: Power Requirements and Specifications

Summary of Contents for SRX240 Series










































































































































































Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands

Juniper SRX240 Series, Hardware Manual

Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands