Juniper SRX240 Series Hardware Manual Download

Page: 56 / 198

Table 20: AC Power Cord Specifications

(continued)

Model Number

Country

CBL-JX-PWR-UK

United Kingdom

WARNING:

The AC power cord for the services gateway is intended for use

with the services gateway only and not for any other use.

Documentation

SRX240 Services Gateway Site Electrical Wiring Guidelines on page 35

•

SRX240 Services Gateway Grounding Specifications on page 59

•

SRX240 Services Gateway Power Supply on page 25

•

SRX240 Services Gateway DC Power Specifications and Requirements on page 38

SRX240 Services Gateway DC Power Specifications and Requirements

This topic includes the following sections:

•

DC Power System Electrical Specifications on page 38

•

DC Power Cable Specifications on page 38

DC Power System Electrical Specifications

Table 21 on page 38

lists the DC power system electrical specifications.

Table 21: DC Power Supply Specifications for the SRX240 Services
Gateway

Specification

Power Requirement

Operating range: –40.5 to –72 VDC

DC input voltage

5A @ -48 VDC

DC system current rating

DC Power Cable Specifications

Table 22 on page 38

summarizes the specifications for the power cables, which you must

supply.

Table 22: DC Power Supply Cable Specifications for the SRX240 Services
Gateway

Specification

Cable Type

Four 12-14 AWG (3.31 to 2.08 mm2), minimum 60°C wire, or as
permitted by the local code.

Power

SRX240 Services Gateway Hardware Guide

Summary of Contents for SRX240 Series










































































































































































Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands

Juniper SRX240 Series, Hardware Manual

Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands