Juniper SRX240 Series Hardware Manual Download

Page: 65 / 198

CHAPTER 9

Installation Overview

•

Installation Overview for the SRX240 Services Gateway on page 47

•

Required Tools and Parts for Installing and Maintaining the SRX240 Services
Gateway on page 48

•

SRX240 Services Gateway Autoinstallation Overview on page 49

Installation Overview for the SRX240 Services Gateway

After you have prepared your installation site, you are ready to unpack and install the
services gateway. It is important to proceed through the installation process as shown
in

Table 27 on page 47

Table 27: Installation Process Sequence for the SRX240 Services Gateway

For More Information

Process

Steps

“SRX240 Services Gateway Safety
Requirements, Warnings, and
Guidelines” on page 139

Review the safety guidelines.

“Site Preparation Checklist for the
SRX240 Services Gateway” on page 29

Verify that you have prepared your site
for the installation of the services
gateway using the checklist.

“Unpacking the SRX240 Services
Gateway” on page 51

Unpack the services gateway and verify
that the parts are received.

“Preparing the SRX240 Services
Gateway for Installation” on page 53

Prepare the services gateway for
installation.

“Installing the SRX240 Services
Gateway” on page 53

Install the services gateway.

Summary of Contents for SRX240 Series










































































































































































Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands

Juniper SRX240 Series, Hardware Manual

Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands