Juniper SRX240 Series Hardware Manual Download

Page: 78 / 198

•

SRX240 Services Gateway AC Power Specifications and Requirements on page 37

•

SRX240 Services Gateway Power Supply on page 25

Grounding the SRX240 Services Gateway

The following tools and parts are required for grounding the SRX240 Services Gateway:

•

Grounding cable for your services gateway—The grounding cable must be minimum
14 AWG (2 mm²), minimum 90°C wire, or as permitted by the local code.

•

Grounding lug—Ring-type, vinyl-insulated TV14-6R lug or equivalent for your grounding
cable

•

Washers and 10-32x.25-in. screws to secure the grounding lug to the protective earthing
terminal

•

Phillips (+) screwdrivers, numbers 1 and 2

Figure 14 on page 60

shows the SRX240 grounding point.

Figure 14: Grounding the SRX240 Services Gateway

You ground the device by connecting a grounding cable to earth ground and then attaching
it to the chassis grounding points using one M3 screw.

Table 33 on page 60

lists the specifications of the grounding cable used with the device.

Table 33: Grounding Cable Specifications for the Services Gateway

Specification

Grounding Requirement

14 AWG single-strand wire cable

Grounding cable

Up to 4 A

Amperage of grounding cable

Ring-type, vinyl-insulated TV14-6R lug or
equivalent

Grounding lug

SRX240 Services Gateway Hardware Guide

Summary of Contents for SRX240 Series










































































































































































Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands

Juniper SRX240 Series, Hardware Manual

Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands