Juniper SRX240 Series Hardware Manual Download

Page: 84 / 198

Connecting to the CLI at the User End for the SRX240 Services Gateway

To remotely connect to the CLI through a dial-up modem connected to the console port
on the services gateway:

Connect a modem at your remote location to a management device such as a PC or
laptop computer.

Start your asynchronous terminal emulation application (such as Microsoft Windows
HyperTerminal) on the PC or laptop computer.

Select the

COM

port to which the modem is connected (for example,

COM1

Configure the port settings shown in

Table 35 on page 66

Table 35: Port Settings for Connecting to the CLI at User End

Value

Port Setting

9600

Bits per second

Data bits

None

Parity

Stop bits

None

Flow control

In the HyperTerminal window, enter

For more information on the AT commands, see the following topics:

•

Initial Configuration for Security Devices

•

Monitoring and Troubleshooting for Security Devices

response verifies that the modem can communicate successfully with the

COM

port on the PC or laptop.

Dial the modem that is connected to the console port on the services gateway by
entering

ATDT

remote-modem-number

. For example, if the number of the modem

connected to the console port on the services gateway is

0013033033030

, enter

ATDT

0013033033030

The services gateway login prompt appears.

root

. No password is required at initial connection, but you must

assign a root password before committing any configuration settings.

Documentation

•

Connecting to the SRX240 Services Gateway Setup Wizard on page 83

•

Connecting the SRX240 Services Gateway to the CLI on page 85

•

Connecting the Modem at the SRX240 Services Gateway End on page 64

SRX240 Services Gateway Hardware Guide

Summary of Contents for SRX240 Series










































































































































































Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands

Juniper SRX240 Series, Hardware Manual

Search results

Summary of Contents for SRX240 Series

Reviews:

Related manuals for SRX240 Series

Brands by name

Popular brands