Juniper SRX3400 Hardware Manual Download

Page: 31 / 232

Table 9: Switch Fabric Board LED Indicators

(continued)

Indicated Behavior

Status

Color

Label

The SFB and all installed CFM cards are operating
normally. The

SERVICE

LEDs on all installed CFM

cards are green.

On steadily

Green

SERVICE

(top)

The SFB or one or more of the installed CFM cards
has reported a minor error condition. The

SERVICE

LEDs on the CFM cards reporting the error are
amber.

On steadily

Amber

The SFB or one or more of the installed CFM cards
has failed. The

SERVICE

LEDs on the failed CFM

cards are red.

On steadily

Red

One or more of the installed CFM cards are disabled.
The

SERVICE

LEDs on the disabled CFM cards are

dark.

Off

Dark
(unlit)

The SFB and all installed CFM cards are operating
normally. The

OK/FAIL

LEDs on all installed CFM

cards are green.

On steadily

Green

OK/FAIL

(bottom)

The SFB or one or more of the installed CFM cards
has failed. The

OK/FAIL

LEDs on the failed CFM

cards are red.

On steadily

Red

One or more of the installed CFM cards are offline.
The

OK/FAIL

LEDs on the offline CFM cards are dark.

Off

Dark
(unlit)

Routing Engine Status (pair)

The Routing Engine in RE0 is functioning as the
master Routing Engine. Only one Routing Engine
can be installed.

On steadily

Green

RE0

(top)

The Routing Engine in slot RE0 is initializing.

Blinking

Either the Routing Engine or Control Board function
on RE0 has failed and is not operating normally.

On steadily

Red

The RE0 slot is empty.

Off

Dark
(unlit)

Unused.

RE1

(bottom)

Power and Fan (pair)

Chapter 2: SRX3400 Services Gateway Hardware Components

Summary of Contents for SRX3400






















































































































































































































Search results

Summary of Contents for SRX3400

Reviews:

Related manuals for SRX3400

Brands by name

Popular brands

Juniper SRX3400, Hardware Manual

Search results

Summary of Contents for SRX3400

Reviews:

Related manuals for SRX3400

Brands by name

Popular brands