10
4 - INSTALLATION
For easy installation proceed as follows:
4.1 - Fix the wall brackets.
4.2 - Fix the canopy hood.
4.3 - Connect the hood to the mains supply and ensure that it works properly.
4-4 - Set the hood for recirculation or evacuation.
4.5 - Fix the telescopic chimney stack.
4.1 - Fixing the wall brackets (fig. 2a-b):
1 - Draw a vertical line on the wall, from the centre of the cooking appliance up to the ceiling,
using a marking pen. This is to ensure the correct vertical alignment of the wall fixing
brackets.
2 - Fixing the wall brackets item
1
a) put the bracket
I
to the wall, aligning its marked centre across the vertical line, ensuring
that the distance between the centres of the holes and the cooking area ia as follows:
1 - when the splasback is to be installed:
d
= 240 mm +
H,
where
H
is the height of the
visible part of the splashback; as the splashback can be of different heights, the correct
figure can only be obtained by measuring the actual height of the splash-back to be fitted.
2 - without splashback:
d
= 890 mm minimum.
Note: ensure that the wall bracket (I) is levelled. The hood can be aligned or adjusted in
height by rotating the adjustment screws (see below).
b) mark on the wall the centres of the two keyholes of the bracket.
3 -
Fixing the wall brackets item
2
a) Place one of the two brackets about 1 or 2 mm from the ceiling or from a horizontal line
drawn between the top of the adjoining wall cabinets, ensuring that the bracket is level.
b) Mark the centres for the keyhole bracket fixing screws.
c) Place the other wall bracket on the wall at
“X”
distance
(see fig.2)
. This measure-ment
should be determined by the height of the upper chimney stack and mark the centres for
the keyhole bracket fixing screws.
d) Mark the centres for the keyhole bracket fixing screws.
4 - Pilot drill all the hole positions as marked on the wall using an 8 mm drill and fix the wall
brackets
1
-
2
using the rawl plugs and screws supplied.
5 - Splashback (optional)
When a splashback is to be fitted, the distance between the cooker hood and the cooking ap-
pliances will be determined by the height of the splashback, item
B
. The splashback is to be
installed
before
installing the canopy. If the splashback is to be fixed to the wall using both the
top
and
bottom
fixing holes care must be taken to ensure that the splashback is fitted at the
correct height
before fixing it into position. The fitting should be undertaken by a a com-
petent person with experience in this type of installation. If the splashback is to be fixed
through
only
the
top
fixing holes proceeds as follows:
a) Put the splashback on the worktop as illu-strated in
fig. 2a
; then holding it against the wall
to ensure that it is correctly positioned mark the holes for the top fixing screws on the wall.
b) Pilot drill the wall using an 8 mm drill and fix the splashback using the 8 mm rawl plugs
and screws supplied.
c) If the fixing holes in the bottom of the splashback are not to be used to secure the
splashback to the wall the installer should ensure that the bottom edge is tucked down
behind the rear of the worktop.
Part 1
a
- INSTALLATION INSTRUCTIONS
Summary of Contents for JDK7530E
