background image

11

www.juwent.com.pl

10. AUTOMATICS

We can deliver the following items to the units:

- Supply and control box: Surface-mounted in the closed casing (equipped with a main switch, 

overcurrent  circuit  breakers,  short-circuit  protection  devices,  signalling  lamps),  intended  to 

cooperate and control the elements of automatics.

One  control  box  allows  controlling  a  group  of  the  units  by  means  of  single  thermostat  in  the 

AUTOMAT|MANUAL operation mode.

The supply and control box (1~230V/50Hz) should be from the main switchboard equipped with a 

main switch and differential protection device.

When the automatics are ordered with the unit the electric diagrams of the unit and automatics are 

delivered by the company as well.

The exemplary connection diagrams of the units with single-phase motors are presented in the 

pictures 2, 3, 4 and 5.

- Rotational speed controllers of the fan: The transformer 5-step rotational speed controllers ARW 

(1~230V/50Hz) allow controlling the air delivery and thermal power. The individual rotational speed 

steps are selected manually.

Controller type

ARW-1,2

ARW-3

PE-L1-N Input voltage (230V AC)

PE,U1,U2 Output (control) voltage

Voltage [V]

230

230

Protection rating

21

21

Height [mm]

123

173

Width [mm]

77

90

Depth [mm]

71

89

- Room thermostat: A room thermostat (on-off) TP allows setting the required temperature in the 

room within the range of 8...30

O

C by means of a knob, however, the room thermostat (on-off) TPP 

allows setting the required temperature in the room within the range of 8...35

O

C in the day and night 

mode on the liquid-crystal display.

Termostat TP or TP/IP65

Supply voltage

24..250V  AC

24..250V  AC

L-Y1 Heating

L-Y2 Cooling

Measurement 

range

8...+30

O

C

8...+35

O

C

Contact rating

6(2)A

10(1,5)A

Protection 

rating

IP30

IP65

Thermostat with time programmer TPP

Supply voltage

2 batteries 1,5V

Q11-Q14 Heating

Q11-Q12 Cooling

Measurement range

5...+35

O

C

Contact rating

5(2)A

Protection rating

IP30

Summary of Contents for TROPIC-1





















Reviews: