background image

June 30, 2003 6:18 pm

Page 20

— 20 —

Master Page: Right

Editing from a camcorder

All necessary cables can be obtained from your dealer.

You can also use another video recorder as the player instead of 
a camcorder.

When you select “EDIT” to dub tapes, be sure to select “AUTO” 
(or “NORM” when the B.E.S.T. function is set to “OFF”) after 
you finish dubbing the tapes.

You can use a camcorder as the source player and your video 
recorder as the recorder.

A

Make connections

a

If the camcorder has no S-VIDEO output connector... 
... connect the camcorder's AUDIO/VIDEO OUT connectors to 
the recorder's front panel AUDIO/VIDEO input connectors.

b

If the camcorder has an S-VIDEO output connector... 
... connect the camcorder's S-VIDEO OUT and AUDIO OUT 
connectors to the recorder's front panel S-VIDEO(S-2) and 
AUDIO input connectors. The recorder's rear panel S-VIDEO IN 
and AUDIO IN input connectors are also available.

When using a monaural camcorder, connect its AUDIO OUT 
connector to the AUDIO L input connector on your recorder.

When a Master Edit Control-equipped JVC camcorder is used, 
the camcorder is capable of controlling the recorder. Refer to 
the camcorder's instruction manual for operating procedure.

B

Set recorder’s input mode

Press 

number key

 “0” and/or 

PR +/–

 to select “F-1” for the 

AUDIO/VIDEO input connectors, or “S-2” for the AUDIO/S-
VIDEO input connectors, depending on the connectors being 
used.

C

Select “EDIT” for picture control set mode

Follow the “Picture Control” section on page 15, then select 
“EDIT.”

D

Start camcorder

Engage its Play mode.

E

Start recorder

Engage its Record mode.

Edit to or from Another Video Recorder

Editing

IMPORTANT

To edit, both the player and the recorder must be of the same 
colour system. Select the appropriate colour system (

16).

PAL, SECAM and NTSC camcorders can be used as a player 
for editing.

a

 If the camcorder has no S-VIDEO output connector...

b

 If the camcorder has an S-VIDEO output connector...

Audio/Video Cable 
(not provided)

AUDIO 
input

VIDEO input

AUDIO OUT

VIDEO OUT

Player

Camcorder

Recorder

Audio Cable (not provided)

AUDIO 
input

S-VIDEO (S-2) 
input

AUDIO OUT

S-VIDEO OUT

Player

Camcorder

Recorder

S-Video Cable (provided)

(MONO)

     

(MONO)

     

TV Receiver

Your recorder

Recorder

Player

Another recorder

AV Cable 
(not provided)

RF Cable 
(provided)

VIDEO 
CHANNEL

TV Receiver

Your recorder

Recorder

Player

Another recorder

AV Cable 
(not provided)

RF Cable (provided)

VIDEO CHANNEL

HR-S6960AA_EN.fm  Page 20  Monday, June 30, 2003  6:18 PM

Summary of Contents for 0703-AH-PJ-BJ





























Reviews: