Masterpage:Right+
EN
73
Filename [MX1SEU_12Editing.fm]
EDITING
Page 73
Monday, 6 December 2004 14:01
SAT S-VIDEO
:
If a connected satellite receiver’s output is compatible with Y/C
signals, set to
A
SAT S-VIDEO
B
. You can obtain a high-quality
S-VHS picture. (For connection, be sure to use a 21-pin
SCART cable that is compatible with the Y/C signal.)
DECODER
:
To use a decoder connected to the [L-2 IN/DECODER] connector.
NOTES:
●
If you have a satellite receiver or a decoder connected to the [L-2
IN/DECODER] connector, be sure to set
A
L-2 SELECT
B
back to
appropriate mode after editing.
●
If you are not connecting a satellite receiver or a decoder to the
[L-2 IN/DECODER] connector, leave
A
L-2 SELECT
B
set to
A
VIDEO
B
.
●
When
A
L-2 SELECT
B
is set to
A
SAT VIDEO
B
and
A
SAT S-VIDEO
B
,
A
SAT
B
appears on the TV screen or front display panel instead of
A
L-2
B
.
●
If
A
L-1 OUTPUT
B
is set to
A
SCART S-VIDEO
B
, it is not possible to
set
A
L-2 SELECT
B
to
A
DECODER
B
or
A
SAT VIDEO
B
.
●
If
A
L-1 OUTPUT
B
is set to
A
SCART RGB
B
, it is not possible to set
A
L-2 SELECT
B
to
A
DECODER
B
or
A
SAT S-VIDEO
B
.
●
If
A
L-1 OUTPUT
B
is set to
A
COMPONENT
B
and
A
L-2 SELECT
B
to
A
SAT VIDEO
B
,
A
SAT S-VIDEO
B
or
A
DECODER
B
, be sure to
connect the [L-1 IN/OUT] connector with a TV.
●
If
A
L-2 SELECT
B
is set to
A
SAT S-VIDEO
B
, be sure to set
A
L-1
OUTPUT
B
to
A
SCART S-VIDEO
B
.
F-1 Input Setting
Set
A
F-1 INPUT
B
to the appropriate mode depending on the
connector (VIDEO or S-VIDEO) being used on the front panel.
1
Perform steps
1
and
2
of
A
L-1 Output And L-1 Input Setting
B
(
A
pg. 72).
2
Press
F G
to select
A
F-1 INPUT
B
, then press
ENTER
.
3
Press
F G
to select the
appropriate setting, then press
ENTER
.
4
Press
SET UP
to complete the
setting.
* The
boldface
settings below indicate the settings at your purchase.
8
F-1 INPUT
^
VIDEO
/
S-VIDEO
VIDEO
:
When connecting an appliance to the [VIDEO] input connector,
set to
A
VIDEO
B
.
S-VIDEO
:
When connecting an appliance to the [S-VIDEO] input
connector, set to
A
S-VIDEO
B
.
You can dub selected audio from a DVD or Audio CD disc to a
digital audio device.
However, it is not possible to dub copy-protected discs.
Example: Dubbing to an MD
1
Connect the unit and a digital audio device using either an
optional optical cable or an optional coaxial cable.
2
Place a disc on the unit and load an MD on the connected
digital audio device.
3
Select the audio to be dubbed.
4
Start playback slightly before the actual point from where you
wish to start dubbing.
5
Press
W
to pause playback.
6
Select the input mode on the connected digital audio device.
7
Press
I
to start playback on the unit.
8
Start recording on the digital audio device.
9
Stop recording on the digital audio device. Then press
o
to stop
playback on the unit.
NOTE:
There may be a discrepancy of several seconds between where
you intend editing to start, and where it actually starts.
ENTER
SELECT
SET UP
EXIT
DVD VIDEO SET UP
MONITOR TYPE
HDD/DVD SET UP
FUNCTION SET UP
INITIAL SET UP
REC/PLAY SET UP
DISPLAY SET
F-1 INPUT
L-1 OUTPUT
L-1 INPUT
L-2 SELECT
VIDEO IN/OUT
4:3LB
VIDEO
VIDEO
SCART VIDEO
VIDEO
VIDEO
VIDEO
S-VIDEO
SELECT WITH @ THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
Digital Audio Dubbing
●
Turn on the TV and select the AV mode.
●
Slide the
TV/CABLE/SAT/DVD
switch to
DVD
.
Rear of unit
Note for connection:
Remove the protection cap from the optical cable.
Digital audio device
(MD deck, etc.)
Coaxial cable
(not supplied)
Player
Recorder
To [DIGITAL
AUDIO OUT
(COAXIAL)]
Optical cable
(not supplied)
To [DIGITAL
AUDIO OUT
(OPTICAL)]
MX1SEU_00.book Page 73 Monday, December 6, 2004 2:01 PM
