F-76
Enregistrement synchrone
Édition d’opérations dans l’écran REMOTE CONTROL (9PIN REC/DV SLAVE) (suite)
4. Lancement du processus d’enregistrement
䡵
Utiliser la source non linéaire pour commander l’enregistreur de DVD.
●
Chaque enregistrement sera stocké sur le disque sous la forme d’un titre unique.
●
L’enregistrement des signaux vidéo et audio sur le DVD sera effectué entre les points d’entrée et de sortie et les chapitres
seront créés automatiquement suivant les indications.
6. Fin du processus d’enregistrement
Remarques
●
Si aucun point IN n’a été défini, l’enregistrement commence en réponse aux commandes REC. Cependant, étant donné que
des codes d’heure sont définis pour les marques de chapitres en tant que valeurs relatives par rapport au point IN, les
chapitres peuvent ne pas être créés comme souhaité. Il est donc recommandé de toujours spécifier le point IN lorsque des
chapitres doivent être créés.
●
Si la fonction de création automatique de chapitre est utilisée, les chapitres seront créés aux intervalles spécifiés.
䡵
Si le disque enregistré doit être lu sur cet enregistreur de DVD
ou sur un autre lecteur, sélectionner FINALIZE et appuyer sur
SET.
Aucun enregistrement supplémentaire ne sera possible sur ce
disque après la finalisation.
䡵
Sélectionner l’élément EXIT à l’écran, appuyer sur la touche
“Entrée” et l’écran REMOTE CONTROL disparaît.
䡵
Appuyer sur la touche OPEN/CLOSE en face avant pour sortir
le disque du BD-X200.
5. Sauvegarde d’une liste d’édition
Élément EDL
Des listes d’édition peuvent être sauvegardées dans l’écran EDL
MANAGER de cet appareil. Des listes d’édition enregistrées dans
l’écran EDL MANAGER peuvent également être lues dans l’écran
REMOTE CONTROL.
䡵
Sélectionner l’élément EDL à l’écran, appuyer sur la touche
“Entrée” et l’écran EDL MANAGER apparaît.
☞
Reportez-vous à la page 69 pour plus d’informations sur
l’utilisation de l’écran EDL MANAGER.
IN POINT
OUT POINT
EXIT
REMOTE CONTROL SCREEN ( DV SLAVE )
1
:
4
7
h
:
m
:
s
f
2
:
5
8
3
6
9
h
:
m
:
s
f
:
h
:
m
:
s
f
CHAPTER
MANUAL
BITRATE
8.0 Mbps
DISC REMAIN
000 min
EDL
TC CANCEL
ADJ
FINALIZE
00:00:00:00
00:00:00:00
00:25:00:00
00:40:00:00
00:15:00:00
00:30:00:00
00:45:00:00
00:20:00:00
00:35:00:00
00:50:00:00
00:10:00:00
FINALIZE
IN POINT
OUT POINT
EXIT
REMOTE CONTROL SCREEN ( DV SLAVE )
1
:
4
7
h
:
m
:
s
f
2
:
5
8
3
6
9
h
:
m
:
s
f
:
h
:
m
:
s
f
CHAPTER
MANUAL
BITRATE
8.0 Mbps
DISC REMAIN
000 min
EDL
TC CANCEL
ADJ
FINALIZE
00:00:00:00
00:00:00:00
00:25:00:00
00:40:00:00
00:15:00:00
00:30:00:00
00:45:00:00
00:20:00:00
00:35:00:00
00:50:00:00
00:10:00:00
Élément EXIT