– 12 –
English
Listening to FM and AM Broadcasts
Tuning in a Station
1
Press FM/AM.
The unit automatically turns on and
tunes in the previously tuned station
(either FM or AM).
• Each time you press the button, the
band alternates between FM and AM.
2
Start searching for stations.
On the unit:
Press and hold or
TUNING – for more than 1
second.
On the remote control:
Press and hold
¢
NEXT
or
4
PREV for more than
1 second.
The unit starts searching for stations and stops when a
station of sufficient signal strength is tuned in.
• If a program is broadcast in stereo, the ST (stereo)
indicator lights up.
To stop searching, press or TUNING – (or
¢
NEXT/
4
PREV on the remote control).
When you press or TUNING – (or
¢
NEXT/
4
PREV on the remote control) briefly and repeatedly
The frequency changes step by step.
To change the FM reception mode
When an FM stereo broadcast is hard to receive
or noisy, press FM MODE on the remote
control so that the MONO indicator lights up on
the display. Reception improves.
To restore the stereo effect, press FM MODE again so that
the MONO indicator goes off. In this stereo mode, you can
hear stereo sounds when a program is broadcasted.
Presetting Stations
You can preset 30 FM and 15 AM stations.
In some cases, test frequencies have been already memorized
for the tuner since the factory examined the tuner preset
function before shipment. This is not a malfunction. You can
preset the stations you want into memory by following the
presetting method.
• There is a time limit in performing the following steps. If
the setting is canceled before you finish, start from step 1
again.
On the unit ONLY:
1
Tune in the station you want to preset.
• See “Tuning in a Station.”
2
Press SET/DISPLAY.
3
Turn
4
/
¢
to select a preset
number.
4
Press SET/DISPLAY again.
The tuned station in step 1 is stored in the
preset number selected in step 3.
• Storing a new station on a used number erases the
previously stored one.
When you unplug the AC power cord or if a power failure
occurs
The preset stations will be erased in a few days. If this happens,
preset the stations again.
Tuning in a Preset Station
1
Press FM/AM.
The unit automatically turns on and
tunes in the previously tuned station
(either FM or AM).
• Each time you press the button, the
band alternates between FM and AM.
2
Select a preset number.
On the unit:
Turn
4
/
¢
.
On the remote control:
Press the number buttons.
Ex.: For preset number 5, press 5.
For preset number 15, press
+10, then 5.
For preset number 20, press
+10, then 10.
For preset number 25, press
+10, +10, then 5.
For preset number 30, press
+10, +10, then 10.
EN01-12.CA-MXGT95/85/75[US,UY]2
31/07/2001, 10:36 am
12
Summary of Contents for CA-MXG75V
