background image

– 13 –

English

Playing Back CDs (CD/CD-R/CD-RW)

This unit has been designed to playback the following CDs:
• CD (Audio CD)
• CD-R (CD-Recordable)
• CD-RW (CD-ReWritable)

Continued use of irregular shape CDs (heart-shape,
octagonal, etc.) can damage the System.

General Notes

In general, you will have the best performance by keeping
your CDs and the mechanism clean.
• Store CDs in their cases, and keep them in cabinets or on

shelves.

• Keep the system’s disc trays closed when not in use.

When playing a CD-R or CD-RW

User-edited CD-Rs (CD-Recordable) and CD-RWs
(CD-ReWritable) can be played back only if they are already
“finalized.”
• You can playback your original CD-Rs or CD-RWs

recorded in music CD format. (However, they may not be
played back depending on their characteristics or recording
conditions.)

• Before playing back CD-Rs or CD-RWs, read their

instructions or cautions carefully.

• Some CD-Rs or CD-RWs may not be played back on this

unit because of their disc characteristics, damage or stain
on them, or the player’s lens is dirty.

• CD-RWs may require a longer read-out time. This is

caused by the fact that the reflectance of CD-RWs is lower
than for regular CDs.

CORRECT

INCORRECT

Loading CDs

On the unit ONLY:

1

Press 

0

 for the disc tray

(CD1, CD2 and CD3) you
want to load a CD onto.

The unit automatically turns on and
the disc tray comes out.

2

Place a disc correctly on the circle of the disc
tray, with its label side up.

• When using a CD single (8 cm), place it on the inner

circle of the disc tray.

3

Press the same 

0

 you have

pressed in step 1.

The disc tray closes, and the
corresponding disc number lamp and
disc indicator light up on the display
(CD1, CD2, and CD3).

4

Repeat steps 1 to 3 to place other CDs.

When loading more than one CD continuously

When you press 

0

 for the next tray you want to place another CD

onto, the first disc tray automatically closes and then the next tray
comes out.

About the disc indicators

Each disc indicator corresponds to the disc tray of the same number.

• The disc marker lights up for the disc number you have selected.
• The disc indicator flashes while the corresponding CD is being

played.

• The disc indicator goes off when the unit has detected that there is

no CD on the corresponding disc tray.

Reminder!
If CD Optical Digital Output is connected during TOC reading, skip
sound will be heard on the speaker.

If you close the tray which has no disc, it will automatically skip to
another tray and start playing. When this happen, press STOP button
to stop it.

Disc number

Disc indicator

Disc marker

EN13-21.CA-MXGT95/85/75[US,UY]2

31/07/2001, 10:36 am

13

Summary of Contents for CA-MXG75V























































Reviews: