– 15 –
English
Programming the Playing Order of the Tracks
— Program Play
You can arrange the order in which tracks play before you
start playing. You can program up to 50 tracks.
• To use Repeat play (see page 16) for Program play, press
REPEAT after starting Program play.
• There is a time limit in performing the following steps. If the
setting is canceled before you finish, start from step 2 again.
1
Load CDs.
• If the current playing source is not the CD player, press
CD
3¥8
SELECT, then
7
before going to the next step.
2
Press PROGRAM so that
“PROGRAM” appears on the
display.
The PRGM (program) indicator also lights up on the
display.
• If a program has been stored in memory, the program is
called up.
3
Press one of the disc number
buttons (CD1, CD2, and CD3)
to select the disc number you
want to program.
4
Select a track from the CD
selected in the above step.
On the unit:
Turn
4
/
¢
to select the
track number and press
SET/DISPLAY.
On the remote control:
Press the number buttons.
• For how to use the number buttons, see “To
go to another track directly using the
number buttons” on page 14.
5
Program other tracks you want.
• To program tracks from the same disc, repeat step 4.
• To program tracks from a different disc, repeat steps 3
and 4.
6
Press CD
3¥8
SELECT.
The tracks are played in the order you
have programed.
To stop playing, press
7
.
To exit from Program play mode, press PROGRAM again
before or after play. The PRGM (program) indicator goes off.
The program you have made is stored in memory.
• If you try to program a 51st track
“FULL” will appear on the display.
• If your entry is ignored
You have tried to program a track from an empty tray, or a track
number that does not exist on the CD (for example, selecting track
14 on a CD that only has 12 tracks). Such entries are ignored.
•
If the total playing time is 100 minutes or more
“– – : – –” will appear on the display.
•
If you want to eject current program play disc
Press PROGRAM button to exit from program mode and program
indicator disappear from the display.
To check the program contents
Before playing, you can check the
program contents by pressing
¢
NEXT or PREV
4
on the remote
control.
•
¢
NEXT: Shows the programed tracks in the programed
order.
• PREV
4
: Shows them in the reverse order.
To modify the program
Before or after playing, you can erase the last
programed tracks by pressing
CANCEL/DEMO.
• Each time you press the button, the programed
track shown on the display is erased from the program.
• Ejecting a CD will also erase the track numbers
programmed from the ejected CD.
To add tracks to the program before playing, simply select
the track numbers you want to add by following step 4 of the
programming procedure.
To erase the entire program before or after playing, press
7
. “PROGRAM” appears on the display.
The program you have made will be erased:
• when you eject all the CDs.
• when you unplug the AC power cord.
• when a power failure occurs.
Continued
Track number
Disc number
Program step number
EN13-21.CA-MXGT95/85/75[US,UY]2
31/07/2001, 10:36 am
15
Summary of Contents for CA-MXG75V
