Masterpage:Right-FullCol
EN
67
Filename [HM-DH5U_Eng.fm]
*The default setting is
bold
in the table below.
L
“POWER SAVE”
“ON”
“OFF”
When this function is set to “ON”, you can reduce the power consumption. While the
VCR is turned off, the front display panel does not show the clock.
When this function is set to “ON”, an i.LINK device cannot be recognized. As a result, it
is not possible to record a program using the digital tuner’s* timer function. In addition
the device does not pass along data if it is in a branched connection.
*For details of a digital tuner, refer to the instruction manual of the digital tuner.
NOTE:
It takes some time until VCR completes its set up when you turn on the VCR.
L
“S-VHS MODE”
“ON”
“OFF”
You can determine which recording mode - either S-VHS mode or VHS mode - is used
for recording on D-VHS and S-VHS tapes.
When this function is set to “ON”,
you can record on D-VHS and S-VHS tapes with S-
VHS picture quality.
When this function is set to “OFF”,
you can record on D-VHS and S-VHS tapes with
VHS picture quality.
NOTES:
•
To record in S-VHS/VHS mode on D-VHS tape, press [D-VHS] to turn off the [D-VHS] indicator.
•
S-VHS mode allows you to make high quality video recordings with horizontal resolution of 400
lines, comparing with the 230 lines of resolution of conventional VHS recordings. To achieve
the highest quality picture we recommend to record in S-VHS mode. (But remember that a
conventional VHS VCR without SQPB cannot play back S-VHS tapes recorded in S-VHS mode.)
•
S-VHS MODE setting does not affect recording on VHS tapes. Recording on VHS tapes is always
performed in VHS mode except when using S-VHS ET mode (
L
“AV COMPU-
LINK”
“ON”
“OFF”
The [REMOTE PAUSE/AV COMPULINK] terminal on the rear panel can be used as
either the [REMOTE PAUSE] terminal or the [AV COMPULINK] terminal.
When this function is set to “ON”,
you can use this terminal as the [AV COMPULINK]
terminal.
By connecting other JVC’s [AV COMPULINK] components (see the diagram below),
including amplifiers (or receivers) and televisions, one touch control of the audio and
video components linked via their [AV COMPULINK] connectors becomes possible.
For example : simply load a cassette in the VCR and press [PLAY (
I
)] so that the
[AV COMPULINK] components automatically turn on, the TV’s AV
mode is selected and the VCR starts playback. (You do not have to
press [PLAY (
I
)] if the cassette’s record safety tab is removed.)
When this function is set to “OFF”,
you can use this terminal as the [REMOTE PAUSE]
terminal (
NOTES:
•
When the remote control code is set to C or D, the connector cannot be used as [AV
COMPULINK] terminal even if “AV COMPU-LINK” is set to “ON”. It is recommended to set the
remote control code to A when you use this function. (
•
Connection varies depending on the type of JVC TV you have. Refer to the TV’s instruction
manual when making this connection.
JVC TV with AV COMPULINK
This VCR
To S-video in
Mini-plug cable (not supplied)
Audio cable (supplied)
S-video cable (supplied)
To [REMOTE
PAUSE/AV
COMPULINK]
To
[AUDIO
OUTPUT]
To AV COMPULINK
(VCR ONLY)
To [S VIDEO OUTPUT]
To Audio in
HM-DH5U_Eng.fm Page 67 Friday, June 25, 2004 11:42 AM
