32
EN
BASIC OPERATIONS ON DVD DECK
Simulated Surround Effect
It is possible to get a simulated surround effect from your stereo
system. You can enjoy the virtual surround sound with your
2 channel stereo system.
1
Press
ON SCREEN
twice to access the on-screen bar.
2
Press
selection keys
to select
A
B
, then press
ENTER
.
●
A
3D-ON
B
appears above the selected item and Simulated
Surround Effect is activated.
●
Each time you press
ENTER
,
A
3D-ON
B
appears and disappears
alternately.
To clear the on-screen bar
Press
ON SCREEN.
To cancel the simulated surround effect
Press
ENTER
to clear
A
3D-ON
B
from the screen.
NOTES:
●
Simulated Surround Effect works correctly only when playing
back a title recorded in multichannels.
●
Simulated Surround Effect does not affect the DVD VIDEO
bitstream signal from the [DIGITAL AUDIO OUT]
connectors.
●
When Simulated Surround Effect is activated, the settings of
A
ANALOG AUDIO OUT
B
and
A
D. RANGE CONTROL
B
are
disabled. (
A
pg. 70)
●
Simulated Surround Effect cannot be activated under the
following conditions:
●
When the HDD deck is in the recording mode.
●
When the HDD or DVD deck is in the timer standby mode.
●
When a disc containing both the Dolby Digital 5.1 CH and 2 CH
sound formats is playing back a scene that is not in the 5.1 CH
sound format.
Adjusting The Picture Quality
You can obtain optimal picture quality by selecting an appropriate
picture mode.
1
Press
ON SCREEN
twice to access the on-screen bar.
2
Press
selection keys
to select
A
B
, then press
ENTER
. The
pop-up window appears under the selected item.
3
Press
selection keys
to select the desired option, then press
ENTER
.
NORMAL
:
Normally select this option.
CINEMA
:
Suitable for a movie disc, etc.
SHARP
:
Clearer, sharper-edged picture when viewing images with lots
of flat, same-coloured surfaces such as cartoons.
SOFT
:
Select this option when too much noise appears.
To clear the on-screen bar
Press
ON SCREEN
.
Setting The Progressive Mode
You can obtain optimal picture quality by selecting whether the
content on the disc is processed by field (video source) or by frame
(film source).
1
Set the unit to the progressive scan mode. (
A
pg. 72)
2
Press
ON SCREEN
twice to access the on-screen bar.
3
Press
selection keys
to select
A
B
, then press
ENTER
. The
pop-up window appears under the selected item.
4
Press
selection keys
to select the desired option, then press
ENTER
.
AUTO
:
This mode automatically detects film and video content for
progressive playback. When film content is found, flag
detection is used to invoke playback of film data in full screen.
When video content is found, pictures from multiple fields are
used to detect sections with movement, and then this
movement undergoes advanced image processing for output of
sharp, detailed progressive images without any reduction in
image quality where movement occurs. Normally, operation in
this mode is recommended.
FILM
:
Suitable for playing back a progressive scanned film source disc.
VIDEO
:
Suitable for playing back a video source disc. The outlines on
the played back pictures will be soft.
To clear the on-screen bar
Press
ON SCREEN
.
NOTE:
When the progressive mode is set, be sure to set
A
L-1 OUTPUT
B
to
A
COMPONENT
B
(
A
pg. 64). Progressive scan is output only from
[COMPONENT VIDEO OUT] connectors.
DVD-
VIDEO
CHAPTER 99
EACH 0:00
TITLE 99
3D-ON CINEMA
AUTO
DVD-
VIDEO
CHAPTER 99
EACH 0:00
TITLE 99
CINEMA AUTO
DVD-
VIDEO
CHAPTER 99
EACH 0:00
TITLE 99
CINEMA
AUTO
3D-ON
