Masterpage:Right+
EN
57
Filename [DR-MV1SEK_07VCR Operation.fm]
Page 57
April 22, 2004 5:09 pm
OPERATIONS ON VCR DECK
You can programme this unit to timer-record as many as
8 programmes.
If you do not know the PlusCode number for the programme you
wish to record, use the following procedure to set your unit to
timer-record the programme.
1
Load a cassette with the record safety tab intact.
2
Press
VCR/DVD
repeatedly so that the VCR lamp lights up on
the unit.
3
Press
PROG/CHECK
to access the
Programme Check screen.
4
Press
rt
to select the blank
number, then press
ENTER
. The
programme screen appears.
5
Press
w e
to select “START”, then
press
rt
to set the desired start time.
●
Each press of
rt
advances/goes
back the start time in 1-min.
increments.
●
To advance/go back the start time in
30-min. increments, press and hold
rt
.
6
Press
w e
to select “STOP”, then press
rt
to set the desired
stop time.
●
Each press of
rt
advances/goes back the stop time in 1-min.
increments.
●
To advance/go back the stop time in 30-min. increments, press and
hold
rt
.
7
Press
w e
to select “DATE”, then press
rt
to set the desired
date.
●
The current date appears on the TV screen. The date you enter
appears in its place.
8
Press
w e
to select “TV PROG”, then press
rt
to select the
desired channel.
9
Press
REC MODE
to select the desired recording mode. Or
press
w e
to select “SP/LP”, then press
rt
to select the desired
recording mode.
10
Press the number keys to set “VPS/PDC” to “ON” or “OFF”.
* VPS (Video Programme System) recording is not currently available
in the U.K. and not possible with this unit.
11
Press
ENTER
to access the Programme Check screen.
12
Press
PROG/CHECK
to complete timer programming.
“PROGRAM COMPLETED” appears on the TV screen for about 5
seconds, then the normal screen appears. If “PROGRAM
OVERLAPPED” appears on the TV screen, see page 58.
●
To programme another timer, repeat steps
3
–
12
.
13
Press
VCR TIMER
(
#
) to engage the unit’s timer mode. The
VCR timer lamp lights up on the unit and the DVD deck is
automatically selected. Press
1
to turn off the unit. When the
DVD deck is in timer standby mode, the unit is automatically turned
off.
●
To disengage the timer mode, press
VCR TIMER
(
#
) again.
NOTES:
●
To Timer-Record Weekly Or Daily Serials:
— anytime during steps
7
through
9
, press
number key “9”
for
weekly serials or
number key “8”
for daily serials (Monday – Friday).
Either “WEEKLY” or “DAILY” appears on the TV screen. Pressing the
button again makes the corresponding indication disappear.
●
You can programme this unit to timer-record as many as 8
programmes. If you try to programme the unit to record a ninth,
“PROGRAMME FULL” appears on the TV screen. To record the extra
programme, you must first cancel any unnecessary programmes.
(
墌
pg. 58)
●
In case of a power failure after programming, the unit’s memory
backup keeps your selections for approximately 5 seconds.
●
Programmes that start after midnight must have the next day’s date.
●
To record the programmes received by satellite receiver, record on
the DVD discs. For details, refer to “Manual Timer Programming”
(
墌
pg. 46).
PDC Recording
Now available from some TV stations, PDC (Programme Delivery
Control) is a service designed to assure safe, accurate timer
recording. With this system, special code signals are transmitted
together with the audio/video signals. These code signals control
your unit and have precedence over the advertised times which
you may have preset into the timer. This means that your unit will
start and stop recording when the preset TV programmes actually
start and end — even if the broadcast time of a preset TV
programme is changed from what has been advertised. PDC is
currently available nationally on BBC1, BBC2, Ch.4 and Ch.5,
except from a few small relay transmitters. Ch.3 operates a PDC
service in some areas. All channels intend to offer this service in
due course. Check your TV programme listing guide for latest
information. If the channel you intend to record does not offer a
PDC service your unit will not start recording if PDC has been
selected. Be sure to set PDC to “OFF” if PDC is not available on
your selected channel. (See step
7
on page 56.)
NOTES:
●
When you use Manual Timer Programming, set the start time (PDC
time) exactly as advertised in the TV listing. A different time than
advertised will result in no recording.
●
PDC recording is not possible when a satellite receiver or a cable
system is connected to L-2 IN/DECODER connector on your unit.
●
PDC recording is also possible via the L-1 IN/OUT connector.
Manual Timer Programming
●
Make sure that the unit’s built-in clock is set properly.
●
Turn on the unit.
●
Turn on the TV and select the AV mode.
●
Slide the
TV/CABLE/SAT/DVD
switch to
DVD
.
1
4
7
2
5
8
0
3
6
9
PROG/CHECK
ENTER
VCR TIMER (
#
)
rtw
e
VCR/DVD
0 – 9
REC MODE
SAT
DISPLAY
DR-MV1SEK_07VCR Operation.fm Page 57 Thursday, April 22, 2004 5:10 PM
