Masterpage:Right+
EN
59
Filename [MV5SEK_09Advanced Operation.fm]
ADVANCED PLAYBACK
Page 59Wednesday, 31 August 2005 19:58
Still Picture/Frame-By-Frame Playback
1
Press
9
to pause during playback.
●
If there is vertical jitter, press
PR +/–
to correct the picture.
2
Press
9
repeatedly to activate frame-by-frame playback.
●
To resume normal playback, press
4
.
Slow Motion
1
Press
9
to pause during playback.
2
Press and hold
9
for 2 seconds, then release. Press
9
and
release again to return to still picture.
●
To resume normal playback, press
4
.
NOTE:
During slow motion playback, some noise may appear on the TV
screen. Press
PR +
or
–
to eliminate the noises.
High-Speed Search
During playback, press
5
for forward high-speed search, or
3
for reverse high-speed search.
●
Each press of the button increases the search speed for each
direction.
When pressing
5
:
(SP): +5x
{
+7x
(LP): +11x
{
+21x
When pressing
3
:
Once
3
is pressed, reverse search starts in –1x normal playback
speed. After this process, each press of
3
changes the search
speed between –5x and –7x in SP mode, –11x and –21x in LP mode.
(SP):
–
1x
]
–
5x
{
–
7x
(LP):
–
1x
]
–
11x
{
–
21x
●
To resume normal playback, press
4
.
Quick Rewind A Little
During playback, press
. The unit rewinds the picture a little
(about 7 seconds) and resumes playback.
●
If the button is pressed repeatedly, the unit rewinds the pictures
continuously and resumes playback.
Skip Search
During playback, press
1 to 6 times to skip over unwanted
sections.
●
Each press initiates an approximately 30-second period of fast-
motion playback. Normal playback resumes automatically.
●
To resume normal playback, press
4
.
Index Search
Your unit automatically marks index codes at the beginning of each
recording. This function gives you quick access to any one of the 9
index codes in either direction.
NOTE:
Before starting, make sure the unit is in the Stop mode.
Press
2
or
6
to activate Index Search. “
2
1” or “
6
1” is
displayed on the TV screen and search begins in the corresponding
direction.
●
To access index codes 2 through 9, press
2
or
6
repeatedly
until the correct index number is displayed.
Example:
To locate the beginning of B from the current position, press
2
twice.
To locate the beginning of D from the current position, press
6
once.
●
When the specified index code is located, playback begins
automatically.
Advanced Playback (VHS)
●
Turn on the unit.
●
Turn on the TV and select the AV mode.
●
Slide the
TV/DVD
switch to
DVD
.
●
Press
VHS
so that the VHS lamp lights up on the unit.
Clean the video heads using a dry cleaning cassette when:
●
Rough, poor picture appears while a tape is played back.
●
The picture is unclear or no picture appears.
●
“USE CLEANING CASSETTE” appears on the screen (only with
“SUPERIMPOSE” set to “AUTO”). (
墌
pg. 79)
NOTE:
The heads get dirty in the following cases:
●
in an environment prone to extreme temperature or humidity
●
in a dusty environment
●
flaw, dirt or mold on video tapes
●
continuous usage for a long time
ATTENTION:
In the search, still, slow-motion or frame-by-frame playback mode,
●
the picture will be distorted.
●
the noise bars will appear.
●
there may be a loss of colour.
●
you cannot hear the sound.
PR +/–
VHS
Index number
Current position
MV5SEK_00.book Page 59 Wednesday, August 31, 2005 7:58 PM
