7
●
To install the monitor on a wall
You can install the monitor on a wall by changing how the stand
bottom plate is attached.
Installation Only for Authorized Service Personnel
Consult authorized service personnel for the installation of this
unit.
Installation instructions must be followed precisely in order to
prevent accidents.
We are selling this product with the understanding that it will be
assembled and installed by properly trained and qualified service
personnel.
About Accidents/Damages
We are not liable for any damage caused by faulty assembly, faulty
wall mounting, insecure wall mounting, misuse, alterations, or
natural disasters.
●
Please be aware that screw holes and anchor bolts will remain
in the wall surface if the monitor is removed after having been
mounted to the wall.
Long-term use of the LCD display monitor may result in
discoloration of the wall surface due to heat/air emitted by the
display.
Danger
●
Consult authorized service personnel for the installation and
attachment of this unit to the wall. Do not attempt to mount the
unit by yourself.
Improper assembly or installation may cause the unit to fall when
it is mounted, which may result in fatal accidents.
To prevent this happening, check the strength of the materials
in the mounting surface. Check the material strength again after
mounting as well.
Warning
●
Using a monitor other than this product may result in damage or
bodily injury due to the LCD display monitor toppling over.
●
Assemble all screws securely. Failure to do so may result in the LCD
monitor and stand falling down, potentially causing damage or
bodily injury.
●
This unit does not come with anchor bolts for securing it to walls,
etc. Be sure you have materials on hand as appropriate for the
mounting location.
●
The monitor should be mounted to a wall that can adequately
hold the total weight of the monitor and stand over a long
period of time and which can adequately withstand earthquakes,
conceivable vibrations, and other external forces.
●
Mounting On Wooden Walls
The weight of the unit should be borne by the wall posts or studs,
and these should be reinforced if insufficiently strong. Do not
install the Wall Mounting Unit on walls made of plasterboard or
thin plywood. Use the commercially sold screws best suited for the
wall structure and material.
●
Mounting On Concrete Walls
Use commercially sold wall anchors capable of supporting the
weight of the LCD monitor.
●
Do not install the Wall Mounting Unit near the blower or air inlet of
an air conditioner.
●
Do not install the Wall Mounting Unit in a location subject to
frequent vibration, impact or other external forces.
●
Do not install the unit in a location where people may hang on it or
lean against it.
●
Do not block the ventilation holes.
●
Do not install the monitor on a non-vertical wall.
Caution
●
Consult authorized service personnel for electrical work. Using
power cords damaged during installation (i.e., exposed or severed
wiring) may result in fire or electric shock.
●
Conduct the work with adequate working space. Damage or bodily
injury may result from working under unsuitable conditions.
●
Avoid mounting this unit in areas where there is electrical wiring or
water pipes, as fire or electric shock may result.
1
Lay the monitor on a cloth with the LCD panel facing down to
prevent the LCD panel from being damaged. Loosen the stand
screws on the stand support and remove the bottom plate.
2
Temporarily set the stand screws in screw holes “2” and “4” on the
right and left sides of the stand support.
●
Tighten the temporarily set stand screws so that they protrude
from the screw holes by about 4 mm.
3
Tighten commercially available screws in the 6 holes shown in the
figure below to install the monitor on the wall.
4
Hook the temporarily set screws on the stand support in right
and left recesses “A” and “B” on the bottom plate, tighten the two
stand screws in right and left screw holes “D” and finally retighten
the temporarily set screws to lock the stand support and bottom
plate.
Bottom plate
Stand support
Stand screws “2” and “4”
Recesses “A” and “B”
Screw holes “D”
DTE21L417L4G̲EN̲1.indb 7
12.2.24 4:01:01 PM
