(No.52097)
DT-V1910CG
16
HOW TO USE “SETUP MENU”
“SETUP MENU” SCREENS
<SETUP MENU>
FUNCTION SETTING
PICTURE SUB ADJ.
COLOR TEMP./BAL.
SIZE/POSI.ADJ.
DISTORTION ADJ.
STATUS DISPLAY
CONTROL LOCK :ON
all reset
EXIT:MENU ENTER:+
SELECT:
<FUNCTION SETTING>
COLOR SYSTEM
:AUTO
AUTO INPUT
:ON
SYNC SELECT
:INT.
RUSH DELAY TIME
:STD.
TALLY SELECT
:GREEN
REMOTE SYSTEM
:MAKE
E.AUDIO GROUP
:1G
HOUR METER X100 :000
EXIT:MENU ADJUST:- +
SELECT:
<PICTURE SUB ADJ.>
CONTRAST
: 00
BRIGHT
: 00
CHROMA
: 00
PHASE
: 00
NTSC SETUP
: 00
COMPO.LEVEL
: SMPTE
sub menu
reset
EXIT:MENU ADJUST:- +
SELECT:
<COLOR TEMP./BAL.>
COLOR TEMP.
: HIGH
BLUE DRIVE
: 000
RED DRIVE
: 000
GREEN CUTOFF
: 000
BLUE CUTOFF
: 000
RED CUTOFF
: 000
sub menu
reset
EXIT:MENU ADJUST:- +
SELECT:
<SIZE/POSI. ADJ.>
H.SIZE
: 00
H.POSITION
: 00
V.SIZE
: 00
V.POSITION
: 00
ZOOM H.SIZE
: 00
ZOOM V.SIZE
: 00
sub menu
reset
EXIT:MENU ADJUST:- +
SELECT:
<DISTORTION ADJ.>
PINCUSHION
: 00
PIN.BALANCE
: 00
PARALLELOGRAM
: 00
TRAPEZOID
: 00
ROTATION
: 00
sub menu
reset
EXIT:
MENU
ADJUST:- +
SELECT:
<STATUS DISPLAY>
STATUS DISPLAY
:ON
LEVEL METER ch
:31
24
BAR TYPE
:3COLORS
REFERENCE LEVEL
:-20dB
OVER LEVEL
:-4dB
BAR BRIGHTNESS
:HIGH
EXIT:MENU ADJUST:- +
SELECT:
Setting Items
Adjusts with
and
buttons.
See page 12 for
more information on
“
sub-menu” and
“reset”.
Press
.
See page 20.
SETUP MENU
*
T
o
go back the previous MENU,
press MENU.
17
ITEM CONTENTS
AND
ADJUSTMENT RANGE/SETTINGS
FUNCTION SETTING
Selects the control systems for the COLOR SYSTEM,
synchronized signal, RUSH DELA
Y
TIME, tally lamp
colors, and MAKE/TRIGGER terminal.
•
Checks the amount of time that the monitor has been
used.
•
Sets the
AUT
O INPUT
function ON/OFF
. (When an input
card compliant with
AUT
O INPUT
is installed.)
•
Selects the audio channel group for the EMBEDDED
AUDIO. (When an input card compliant with EMBEDDED
AUDIO is installed.)
Press the
button to
display the setting menu
illustrated on the right.
COLOR SYSTEM
Selects the color system when using the video input
card.
AUT
O
:
Changes NTSC and P
A
L
automatically
.
NTSC
:
Keeps the color system NTSC.
PA
L
:
Keeps the color system P
AL.
NOTE:
Normally select
AUT
O. However
, if the input signal is unstable,
select NTSC or P
AL.
AUT
O INPUT
When HD SDI signal and D1 SDI signal need to be
switched to input accordingly by one signal cable,
AUT
O INPUT
automatically detects whether a signal
is being input to Input
A
(HD SDI input card) or Input
C (SDI input card) and switches INPUT
accordingly
.
ON
:
AUT
O INPUT is ON.
OFF
:
AUT
O INPUT
does not function.
NOTES:
• Functions only when input card compatible with
AUT
O INPUT
is
used.
• “INPUT SELECT ERROR” is displayed for approx. 3 seconds
when dif
ferent signal cables are connected to each INPUT
A
and
INPUT C and signals are input to the each of them.
Preparation for the
AUT
O INPUT function (See below
illustration)
1. Insert HD SDI input card to SLOT1, and SDI input card to
SLOT2 (both cards need to be compatible with
AUT
O
INPUT), then connect the signal cable.
2. Input HD SDI signal or D1 SDI signal to HD SDI input
card.
SYNC SELECT
Synchronized signal selection.
INT
.
:
The input video signal is synchronized with the
built-in sync signal.
EXT
.
:
The input video signal is synchronized with an
external signal from an external sync terminal.
RUSH DELA
Y
TIME
Sets the time when the power supply to the monitor
’s
circuits (excluding the micro computers) starts after
the power switch is pressed.
STD.
:
The power supply starts approx.
1 second after the power switch is pressed.
SLOW
:
The power supply starts approx.
3.2 seconds after the power switch is pressed.
NOTE:
If you are going to turn several Multi-Format Monitors on at the
same time, it is recommended to apply SLOW to some of the
monitors to control rush current.
T
ALL
Y
SELECT
Selects the color of the tally lamp (when lit) on the
upper front panel.
GREEN
:
The tally lamp lights in green.
RED
:
The tally lamp lights in red.
REMOTE SYSTEM
Selects the control system for the MAKE/TRIGGER
terminals. Refer to “How to use the MAKE/TRIGGER
terminal” on page 21.
•
MAKE (make contact)/ TRIGGER (trigger contact)
E.AUDIO GROUP
Selects the audio channel group for EMBEDDED
AUDIO. It is displayed when an input card compliant
with EMBEDDED
AUDIO is installed.
•
1G/2G/1-2G
1G
:
2G
:
1-2G
:
NOTE:
The auto setting mixes and outputs all 8 signal channels. Sets the
output level automatically by detecting the number of channels
receiving the signal.
*
About sound output level
Sound output level is set to a standard output level for all
channels when several sound channels are output at the same
time.
The more channels are selected, the lower each channel’
s
level will be.
(Each channel's level becomes half for 1– 2 channel, 1/4 for 1– 4
channel.)
HOUR METER X100h
Displays the total usage time of the monitor in
hundred-hour units.
•
000 ~ 655
NOTES:
•
When the timer passes 655, it returns to 000.
•
The timer does not count the usage time under one hour
.
<FUNCTION SETTING>
COLOR SYSTEM
:AUTO
AUTO INPUT
:ON
SYNC SELECT
:INT.
RUSH DELAY TIME
:STD.
TALLY SELECT
:GREEN
REMOTE SYSTEM
:MAKE
E.AUDIO GROUP
:1G
HOUR METER X100h :000
EXIT:
MENU
ADJUST:- + S
E
L
ECT:
1ch 2ch 3ch 4ch 1-2ch 3-4ch 1-4ch
5ch 6ch 7ch 8ch 5-6ch 7-8ch 5-8ch
A
U
T
O
5-8ch 1-4ch 7-8ch 5-6ch 3-4ch
1ch 2ch 3ch 4ch 5ch 6ch 7ch 8ch 1-2ch
IN
OUT
E.A
UDIO
HD SDI 1
IN1
IN2
SWITCHED
OUT
E.A
UDIO SDI
SLO
T2
SLO
T1
D1 SDI input card
compatible with
AUT
O INPUT
HD SDI input card
compatible with
AUT
O INPUT